;------------------------------------------------------------------------------- ; #alert "alert text goes here - if uncommented, it will be displayed in a pop-up dialog whever a project using this INI is opened" ; INI date: Feb.02/2011 7:52PM PDT [MegaTune] MTversion = 2.25 ; MegaTune itself; needs to match exec version. versionInfo = "S" ; Put this in the title bar. queryCommand = "Q" ; Verify against signature. signature = "MSII Rev 2.88800 " ; MS-II sends a null at 20th byte. ; 123456789.123456789. ;------------------------------------------------------------------------------- ; ; PREAMBLE ; ; There are several main sections (with brackets around the [section] heading) in this INI file: ; ; - Constants - this is divided into two pages (for recent MS-II code versions, ; at least). Page 1 is based on the source code inpram structure ; Page 2 is based on the source code in2ram structure. All of the ; values are inputs sent from MegaTune to the MegaSquirt-II ; - Menu (& User Defined) - these define most of the mennus in MegaTune (except ; those that are 'built-in' like the accel wizrd, etc.) ; - Curve Editor and Table Editor ; - Gauge Configuration ; - Front Page & RuntTime & Tuning Config ; - Burst Mode Config ; - Output Channels - this mirrors the OUTPC structure from the source code. All ; of the values are sent from MegaSquirt-II to MegaTune on the PC. ; - Datalog - select output channels to log to the PC hard drive ; ; Note: ; - To add an input variable to MegaTune, you need to add it to the inpram (or in2ram) ; structure in the MegaSquirt source code noting the correct offset (and recompile, ; of course), to the Constants section, and to one of the menus. ; - To add an output variable to MegaTune (for monitoring, logging, or switching purposes), ; you need to add it to the outpc structure in the source code, to the OuptChannels, and ; to the datalog section (and/or the gauge configurations, if you wish to see it directly ; in MegaTune). ; ; In general, the respective notation for variables from the source code to the INI are: ; ; signed unsigned bytes ; ------ -------- ----- ; - char = S08 U08 1 ; - int = S16 U16 2 ; - long = S32 U32 4 ; ; Where the maximum range is: ; ; signed unsigned ; ------ -------- ; - char = -128 to 127 0 to 255 ; - int = -32768 to 32767 0 to 65535 ; - long = -2147483648 0 to 4294967295 ; to 2147483647 ; ;---------------------------------------------------------------------------- ; Temperature Limits and Settings Reference ;---------------------------------------------------------------------------- ; ; Below is a listing of all of the temperature ranges used throughout the INI for the MegaSquirt II. ; ; CELSIUS (Expanded/Normal): ; Low limit: -40C/-40C ; High limit: 300C/150C ; Low danger: 65C/10C ; Low warning: 93C/65C ; High warning: 162C/93C ; High danger: 176C/104C ; ; FAHRENHEIT (Expanded/Normal): ; Low Limit: -40F/-40F ; High limit: 600F/300F ; Low danger: 150F/50F ; Low warning: 200F/150F ; High warning: 325F/200F ; High danger: 350F/220F ;---------------------------------------------------------------------------- [Constants] ;---------------------------------------------------------------------------- ; Constants Definition ; -------------------- ; ; Scalar Values ; ------------- ; The scaling and translation values are used as follows: ; msValue = userValue / scale - translate ; userValue = (msValue + translate) * scale ; ; I've got no good way to handle a few of these things yet. ; ; Temperatures are fine, check out the Fielding IAC example (fastIdleTemp). ; ; The TPS stuff is a problem, because we have to modify the INI file for ; each TPS installation and again whenever we move the TPS... ; ; Array Values ; ------------ ; Arrays are specified just like scalars, except that they have a "shape" ; entry in the fourth parameter. The shape allows you to define lists or ; tables, for example [8] defines a list with eight values and [2x4] defines ; a table with eight values (two rows and four columns). Tables may be ; stored in either "X-" or "Y-order." X-order means that memory is laid ; out as follows: ; ; [x1,y1] [x2,y1]...[xn,y1] [x1,y2]... ; ; Y-order would be ; ; [x1,y1] [x1,y2]...[x1,yn] [x2,y1]... ; ; To use the TableEditor, you must define two lists and a table, and ; the lengths of the lists must correspond to the shape of the table. ; ; Bit Fields ; ---------- ; Bits are numbered 0-7, the rightmost being bit zero. The basic ; data word that stores bit fields must be unsigned. ; ; You need NOT supply the correct number of labels matching the ; number of bits you've specified (one bit requires 2 values, two ; bits requires 4 values and so on). If you neglect to supply enough ; labels, they will be synthesized using the sequence "1", "2" and so ; on based upon their position in the sequence (the cltType and matType ; will end up with identical lists). ; ;---------------------------------------------------------------------------- pageActivationDelay = 50 ; Milliseconds delay after burn command. blockReadTimeout = 200 ; Milliseconds total timeout for reading page. endianness = big nPages = 2 pageSize = 994, 946 pageIdentifier = "\x00\x04", "\x00\x05" burnCommand = "b%2i", "b%2i" pageReadCommand = "r%2i%2o%2c", "r%2i%2o%2c" pageValueWrite = "w%2i%2o%2c%v", "w%2i%2o%2c%v" pageChunkWrite = "w%2i%2o%2c%v", "w%2i%2o%2c%v" page = 1 ; name = class, type, offset, shape, units, scale, translate, lo, hi, digits nCylinders = bits , U08, 0, [0:3], "INVALID" ; * no_skip_pulses = scalar, U08, 1, "", 1.00000, 0.00000, 1.00, 255.00, 0 ; * ( 1 byte) ICIgnCapture = bits , U08, 2, [0:0], "Falling Edge", "Rising Edge" ; * ICCrankTrigger = bits , U08, 2, [1:2], "Calculated", "Trigger Return", "Trigger Rise", "INVALID" ; * ICIgnOption = bits , U08, 2, [4:5], "Standard Coil Charge", "EDIS", "EDIS Multispark", "INVALID" ; * spkout_hi_lo = bits , U08, 3, [0:0], "Going Low (Normal)", "Going High (Inverted)" ; * max_coil_dur = scalar, U08, 4, "msec", 0.10000, 0.00000, 1.00, 8.00, 1 ; * ( 1 byte) max_spk_dur = scalar, U08, 5, "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) dwellAcc = scalar, U08, 6, "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) dwellVolts = array , S08, 7, [ 5], "V", 0.10000, 0.00000,-12.80, 12.70, 1 ; * ( 5 bytes) dwellDuration = array , S08, 12, [ 5], "msec", 0.10000, 0.00000,-12.80, 12.70, 1 ; * ( 5 bytes) RevLimOption = bits , U08, 17, [0:1], "None", "Spark Retard", "Fuel Cut", "INVALID" ; * ( 1 byte) RevLimMaxRtd = scalar, U08, 18, "deg", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) PredOpt = bits , U08, 19, [0:1], "Last Interval", "Alpha-Beta-Gamma Filter", "INVALID", "INVALID" ; * crankingRPM = scalar, S16, 20, "RPM", 1.00000, 0.00000, 0.00, 3000.0, 0 ; * ( 2 bytes) cold_adv_table = array , S16, 22, [ 10], "deg", 0.10000, 0.00000,-10.00, 10.00, 1 ; * ( 20 bytes) triggerOffset = scalar, S16, 42, "deg", 0.10000, 0.00000,-359.0, 359.00, 2 ; * ( 2 bytes) RevLimRpm1 = scalar, S16, 44, "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 2 bytes) RevLimRpm2 = scalar, S16, 46, "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 2 bytes) #if LAMBDA afrTable1 = array , U08, 48, [12x12], "Lambda", 0.006803, 0.00000, 0.00, 2.00, 3 ; * (144 bytes) afrTable2 = array , U08, 192, [12x12], "Lambda", 0.006803, 0.00000, 0.00, 2.00, 3 ; * (144 bytes) #else afrTable1 = array , U08, 48, [12x12], "AFR", 0.10000, 0.00000, 9.00, 20.00, 1 afrTable2 = array , U08, 192, [12x12], "AFR", 0.10000, 0.00000, 9.00, 20.00, 1 #endif wueBins = array , U08, 336, [ 10], "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 10 bytes) taeBins = array , U08, 346, [ 4], "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 4 bytes) maeBins = array , U08, 350, [ 4], "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 4 bytes) iacstepTable = array , S16, 354, [ 10], "steps", 1.00000, 0.00000, 0.00, 500.00, 0 ; * ( 20 bytes) ipwmTable = array , S16, 354, [ 10], "%", 1.00000, 0.00000, 0.00, 100.00, 0 frpm_table = array , U16, 374, [ 12], "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 24 bytes) srpm_table = array , U16, 398, [ 12], "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 24 bytes) fmap_table = array , S16, 422, [ 12], "kPa", 0.10000, 0.00000, 0.00, 400.00, 1 ; * ( 24 bytes) smap_table = array , S16, 446, [ 12], "kPa", 0.10000, 0.00000, 0.00, 400.00, 1 ; * ( 24 bytes) #if CELSIUS #if EXPANDED_CLT_TEMP tempTable = array , S16, 470, [ 10], "°C", 0.05555, -320.000,-40.00, 300.00, 1 ; * ( 20 bytes) Temperature bins for cranking, cold AE and WUE #else tempTable = array , S16, 470, [ 10], "°C", 0.05555, -320.000,-40.00, 100.00, 1 ; * ( 20 bytes) Temperature bins for cranking, cold AE and WUE #endif #else #if EXPANDED_CLT_TEMP tempTable = array , S16, 470, [ 10], "°F", 0.10000, 0.00000,-40.00, 600.00, 1 #else tempTable = array , S16, 470, [ 10], "°F", 0.10000, 0.00000,-40.00, 200.00, 1 #endif #endif taeRates = array , S16, 490, [ 4], "%/sec", 1.00000, 0.00000, 0.00, 32767.0, 0 ; * ( 8 bytes) tpsDot bins used for AE: x for TAE interpolation maeRates = array , S16, 498, [ 4], "kPa/sec", 1.00000, 0.00000, 0.00, 32767.0, 0 ; * ( 8 bytes) mapDot bins used for AE: x for MAE map0 = scalar, S16, 506, "kPa", 0.10000, 0.00000, -100.0, 3276.7, 1 ; * ( 2 bytes) mapmax = scalar, S16, 508, "kPa", 0.10000, 0.00000, -100.0, 3276.7, 1 ; * ( 2 bytes) #if CELSIUS clt0 = scalar, S16, 510, "°C", 0.05555, -320.000, -100.0, 500.0, 1 ; * ( 2 bytes) cltmult = scalar, S16, 512, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; * ( 2 bytes) mat0 = scalar, S16, 514, "°C", 0.05555, -320.000, -100.0, 500.0, 1 ; * ( 2 bytes) #else clt0 = scalar, S16, 510, "°F", 0.10000, 0.00000, -100.0, 500.0, 1 cltmult = scalar, S16, 512, "%", 1.00000, 0.00000, -200.0, 200.0, 0 mat0 = scalar, S16, 514, "°F", 0.10000, 0.00000, -100.0, 500.0, 1 #endif matmult = scalar, S16, 516, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; * ( 2 bytes) tpsMin = scalar, S16, 518, "ADC", 1.00000, 0.00000, 0.0, 1023.0, 0 ; * ( 2 bytes) tpsMax = scalar, S16, 520, "ADC", 1.00000, 0.00000, 0.0, 1023.0, 0 ; * ( 2 bytes) batt0 = scalar, S16, 522, "V", 0.10000, 0.00000, 0.0, 3276.7, 1 ; ( 2 bytes) battmax = scalar, S16, 524, "V", 0.10000, 0.00000,-3276.8, 3276.7, 1 ; ( 2 bytes) ego0 = scalar, S16, 526, "afr", 0.10000, 0.00000,-3276.8, 3276.7, 1 ; ( 2 bytes) egomult = scalar, S16, 528, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; ( 2 bytes) baro0 = scalar, S16, 530, "kPa", 0.10000, 0.00000,-3276.8, 3276.7, 1 ; * ( 2 bytes) baromax = scalar, S16, 532, "kPa", 0.10000, 0.00000,-3276.8, 3276.7, 1 ; * ( 2 bytes) bcor0 = scalar, S16, 534, "%", 1.00000, 0.00000,-3276.8, 3276.7, 1 ; * ( 2 bytes) bcormult = scalar, S16, 536, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; * ( 2 bytes) knock0 = scalar, S16, 538, "V", 0.01000, 0.00000, 0.0, 5.0, 1 ; * ( 2 bytes) knockmax = scalar, S16, 540, "V", 0.01000, 0.00000, 0.0, 5.0, 1 ; * ( 2 bytes) Dtpred_Gain = scalar, S16, 542, "%", 1.00000, 0.00000, -200.0, 200.0, 0 ; * ( 2 bytes) crankTolerance = scalar, U08, 544, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) asTolerance = scalar, U08, 545, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) pulseTolerance = scalar, U08, 546, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) IdleCtl = bits , U08, 547, [0:2], "None", "Solenoid", "IAC Stepper Moving Only", "IAC Stepper Always On", "PWM Warmup", "15-Minute IAC", "INVALID", "INVALID" ; * IACtstep = scalar, U08, 548, "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) IACaccstep = scalar, U08, 549, "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) IACminstep = scalar, U08, 550, "steps", 1.00000, 0.00000, 1.00, 255.00, 0 ; * ( 1 byte) IACpwm_step = scalar, U08, 551, "Hz", 80.00000, 0.00000, 80.00, 800.00, 0 ; * ( 1 byte) IACStart = scalar, S16, 552, "", 1.00000, 0.00000, 0.00, 4000.00, 0 ; * ( 1 byte) #if CELSIUS IdleHyst = scalar, S16, 554, "°C", 0.05555, 0.00000, 0.0, 30.0, 1 ; * ( 2 bytes) #else IdleHyst = scalar, S16, 554, "°F", 0.10000, 0.00000, 0.0, 50.0, 1 #endif IACcrankpos = scalar, S16, 556, "steps", 1.00000, 0.00000, 0.00, 4000.00, 0 ; * ( 2 bytes) IACcrankxt = scalar, S16, 558, "sec", 1.00000, 0.00000, 0.00,32767.00, 0 ; * ( 2 bytes) #if CELSIUS #if EXPANDED_CLT_TEMP IACcoldtmp = scalar, S16, 560, "°C", 0.05555, -320.000, -40.0, 300.0, 1 ; * ( 2 bytes) #else IACcoldtmp = scalar, S16, 560, "°C", 0.05555, -320.000, -40.0, 150.0, 1 ; * ( 2 bytes) #endif #else #if EXPANDED_CLT_TEMP IACcoldtmp = scalar, S16, 560, "°F", 0.10000, 0.00000,-40.00, 500.00, 1 #else IACcoldtmp = scalar, S16, 560, "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif #endif IACcoldpos = scalar, S16, 562, "steps", 1.00000, 0.00000, 0.00, 4000.00, 0 ; * ( 2 bytes) IACcoldxt = scalar, S16, 564, "sec", 1.00000, 0.00000, 0.00,32767.00, 0 ; * ( 2 bytes) primePulseCold = scalar, S16, 566, "msec", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 2 bytes) primePulseHot = scalar, S16, 568, "msec", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 2 bytes) crankCold = scalar, S16, 570, "msec", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 1 byte) crankHot = scalar, S16, 572, "msec", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 1 byte) asePctCold = scalar, S16, 574, "%", 1.00000, 0.00000, 0.00, 400.00, 0 ; * ( 2 bytes) asePctHot = scalar, S16, 576, "%", 1.00000, 0.00000, 0.00, 400.00, 0 ; * ( 2 bytes) aseCountCold = scalar, S16, 578, "cycles", 1.00000, 0.00000, 0.00,32767.00, 0 ; * ( 2 bytes) aseCountHot = scalar, S16, 580, "cycles", 1.00000, 0.00000, 0.00,32767.00, 0 ; * ( 2 bytes) taeColdA = scalar, U08, 582, "msec", 0.10000, 0.00000, 0.00, 25.500, 1 ; * ( 1 byte) taeColdM = scalar, U08, 583, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) tpsThresh = scalar, U08, 584, "%/sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) mapThresh = scalar, U08, 585, "kPa/sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) threshold for MAE taeTime = scalar, U08, 586, "sec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) tdePct = scalar, U08, 587, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) floodClear = scalar, S16, 588, "%", 0.10000, 0.00000, 0.00, 100.00, 1 ; * ( 2 bytes) TPSOXLimit = scalar, S16, 590, "%", 0.10000, 0.00000, 0.00, 100.00, 1 ; * ( 2 bytes) tpsProportion = scalar, U08, 592, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) baroCorr = bits , U08, 593, [0:1], "None", "Initial MAP Reading", "Two Independent Sensors", "INVALID" ; * egoType = bits , U08, 594, [0:2], "Disabled", "Narrow Band", "Dual Narrow Band", "Single Wide Band", "Dual Wide Band", "INVALID", "INVALID", "INVALID" ; * egoCount = scalar, U08, 595, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) egoDelta = scalar, U08, 596, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) egoLimit = scalar, U08, 597, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) #if NARROW_BAND_EGO egoTarget = scalar, U08, 598, "v", 0.01000, 0.00000, 0.00, 2.00, 4 ; * ( 1 byte) #elif LAMBDA AFRTarget = scalar, U08, 598, "Lambda", 0.006803, 0.00000, 0.00, 2.00, 3 #else AFRTarget = scalar, U08, 598, "AFR", 0.10000, 0.00000, 0.00, 25.50, 1 #endif tempUnits = bits , U08, 599, [0:0], "Coolant/IAT Tables in °F", "Coolant/IAT Tables in °C" ; * ( 1 byte) MAFOption = bits , U08, 600, [0:1], "No MAF", "MAF Only", "MAF/MAP blend", "INVALID", ; * MAFpin = bits , U08, 600, [4:5], "MAF on MAP pin", "MAF on Baro Pin", "MAF on Knock Pin", "INVALID" ; * DualSpkOptn = bits , U08, 601, [0:3], "No Dual Spark", "Dual Tach Inputs", "Falling Cam Sync with Tach or Wheel", "Rising Cam Sync with Tach or Wheel", "Single Crank Wheel Input", "Single Cam Wheel Input", "Dual Inputs, Timing from 1 cam tooth", "M-0 Wheel w/ Falling Crank Sync", "M-0 Wheel w/ Rising Crank Sync", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID", "INVALID" ; * (1 byte) #if CELSIUS #if EXPANDED_CLT_TEMP fastIdleT = scalar, S16, 602, "°C", 0.05555, -320.000,-40.00, 300.00, 1 ; * ( 2 bytes) egoTemp = scalar, S16, 604, "°C", 0.05555, -320.000,-40.00, 300.00, 1 ; * ( 2 bytes) #else fastIdleT = scalar, S16, 602, "°C", 0.05555, -320.000,-40.00, 150.00, 1 ; * ( 2 bytes) egoTemp = scalar, S16, 604, "°C", 0.05555, -320.000,-40.00, 150.00, 1 ; * ( 2 bytes) #endif #else #if EXPANDED_CLT_TEMP fastIdleT = scalar, S16, 602, "°F", 0.10000, 0.00000,-40.00, 600.00, 1 egoTemp = scalar, S16, 604, "°F", 0.10000, 0.00000,-40.00, 600.00, 1 #else fastIdleT = scalar, S16, 602, "°F", 0.10000, 0.00000,-40.00, 300.00, 1 egoTemp = scalar, S16, 604, "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif #endif egoRPM = scalar, S16, 606, "RPM", 1.00000, 0.00000, 0.00, 15000.0, 0 ; * ( 2 bytes) reqFuel = scalar, U16, 608, "msec", 0.00100, 0.00000, 0.00, 65.536, 2 ; * ( 2 bytes) divider = scalar, U08, 610, "", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 1 byte) alternate = bits, U08, 611, [0:0], "Simultaneous", "Alternating" ; * ( 1 byte) injOpen = scalar, U08, 612, "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) injPwmT = scalar, U08, 613, "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) injPwmPd = scalar, U08, 614, "µsec", 1.00000, 0.00000, 40.00, 100.00, 0 ; * ( 1 byte) injPwmP = scalar, U08, 615, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) battFac = scalar, U08, 616, "ms/v", 0.0166667, 0.00000, 0.00, 1.00, 2 ; * ( 1 byte) twoStroke = bits, U08, 617, [0:0], "Four-stroke", "Two-stroke" ; * injType = bits, U08, 618, [0:0], "Port Injection", "Throttle Body" ; * nInjectors = bits, U08, 619, [0:4], "INVALID" ; * OddAng = scalar, S16, 620, "degrees", 0.10000, 0.00000,-350.0, 350.00, 1 rpmLF = scalar, U08, 622, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) mapLF = scalar, U08, 623, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) tpsLF = scalar, U08, 624, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) egoLF = scalar, U08, 625, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) adcLF = scalar, U08, 626, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) knkLF = scalar, U08, 627, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) AMCOption = bits, U08, 628, [0:1], "Disabled", "RAM Update", "FLASH Update", "INVALID" ; * ( 1 byte) dualTable = bits, U08, 629, [0:0], "Single Table", "Dual Table" ; * algorithm = bits, U08, 630, [0:1], "Speed Density", "Blend SD/Alpha-N", "Pure Alpha-N", "INVALID" ; * alpha_baro_spkadv = scalar, U08, 631, "deg/kPa", 0.01000, 0.00000, 0.00, 255.00, 2 ; * ( 1 byte) AfrAlpha = scalar, U08, 632, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; U ( 1 byte) UNUSED AFRStoich = scalar, U08, 633, "AFR", 0.10000, 0.00000, 0.00, 20.00, 1 ; * ( 1 byte) AFRStoichWB = scalar, U08, 633, "AFR", 0.10000, 0.00000, 0.00, 20.00, 1 ; * ( 1 byte) AFRStoichNB = scalar, U08, 633, "Volts", 0.01000, 0.00000, 0.00, 7.00, 3 ; * (1 byte) alpha_lorpm = scalar, S16, 634, "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 2 bytes) alpha_hirpm = scalar, S16, 636, "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 2 bytes) alphaMAPtable = array , S16, 638, [ 6x 6], "kPa", 0.10000, 0.00000, 0.00, 200.00, 1 ; * ( 72 bytes) amap_tps = array , S16, 710, [ 6], "%", 0.10000, 0.00000, 0.0, 100.00, 1 ; * ( 12 bytes) amap_rpm = array , U16, 722, [ 6], "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 12 bytes) baud = scalar, U32, 734, "", 1.00000, 0.00000,9600.0,115200.0, 0 ; x ( 4 bytes) MAPOXLimit = scalar, S16, 738, "kPa", 0.10000, 0.00000, 0.00, 300.00, 2 ; * ( 2 bytes) board_type = scalar, U08, 740, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) mycan_id = scalar, U08, 741, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) fet_delay = scalar, U08, 742, "µsec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) vr_delay = scalar, U08, 743, "µsec/1000rpm", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) ECUType = scalar, U08, 744, "1=MS-II, 2=MicroSquirt", 1.00000, 0.00000, 0.00, 9.00, 0 ; * ( 1 byte) MapThreshXTD2 = scalar, U08, 745, "-kpa/sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) #if n2o n2oEnrich = scalar, U08, 746, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) #else pwImpulse = scalar, U08, 746, "msec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) #endif impulseSec = scalar, U08, 747, "sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) nImpulse = scalar, U08, 748, "", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) mapdotSample = scalar, U08, 749, "msec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) tpsdotSample = scalar, U08, 750, "msec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) ASEHot = bits, U08, 751, [0:0], "Disable ASE on Hot Start", "Enable ASE on Hot Start" InjStart = scalar, U08, 752, "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) MapThreshXTD = scalar, U08, 753, "-kpa/sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) MapThreshXTA = scalar, U08, 754, "kpa/sec", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) trendmapLimit = scalar, U08, 755, "kpa", 1.00000, 0.00000, 0.00, 255.00, 0 ; * ( 1 byte) ; Port Settings constants psEnabled = array , U08, 756, [ 7], "on/off", 1.00000, 0.00000, 0.00, 1.00, 0 ; * ( 2 bytes) psCondition = array , U08, 763, [ 7x2], "", 1.00000, 0.00000,-128.00, 127.00, 0 ; * ( 2 bytes) psConnector = array , U08, 777, [ 7], "", 1.00000, 0.00000,-128.00, 127.00, 0 ; * ( 2 bytes) psInitValue = array , U08, 784, [ 7], "", 1.00000, 0.00000,-128.00, 127.00, 0 ; * ( 2 bytes) psPortValue = array , U08, 791, [ 7], "", 1.00000, 0.00000,-128.00, 127.00, 0 ; * ( 2 bytes) psOutSize = array , U08, 798, [ 7x2], "", 1.00000, 0.00000,-128.00, 127.00, 0 ; * ( 2 bytes) psOutOffset = array , U16, 812, [ 7x2], "", 1.00000, 0.00000,-128.00, 127.00, 0 ; * ( 2 bytes) psThreshold = array , U16, 840, [ 7x2], "", 1.00000, 0.00000,-32768.0,32767.0, 0 ; * ( 4 bytes) psHysteresis = array , U16, 868, [ 7x2], "", 1.00000, 0.00000,-32768.0,32767.0, 0 ; * ( 4 bytes) aeTaperTime = scalar, U08, 896, "sec", 0.10000, 0.00000, 0.00, 25.50, 1 ; * ( 1 byte) AFRMult = bits, U08, 897, [0:1], "Use Combined VE/AFR table", "Separate VE & AFR table w/ NB EGO", "Separate VE & AFR table w/ WB EGO", "INVALID" ; * ( 1 byte) aeEndPW = scalar, S16, 898, "msec", 0.10000, 0.00000, 0.00, 1000.00, 1 ; * egoAlgorithm = bits , U08, 900, [0:1], "Simple", "Transport Delay", "PID/Smith Predictor", "INVALID" ; * ( 1 byte) egoKP = scalar, U08, 901, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) egoKI = scalar, U08, 902, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) egoKD = scalar, U08, 903, "%", 1.00000, 0.00000, 0.00, 100.00, 0 ; * ( 1 byte) egoKdelay1 = scalar, U16, 904, "msec", 1.00000, 0.00000, 0.00, 65535, 0 ; * ( 2 bytes) egoKdelay2 = scalar, U16, 906, "revs", 1.00000, 0.00000, 0.00, 65535, 0 ; * ( 2 bytes) flexFuel = bits , U08, 908, [0:0], "Disabled", "Enabled" ; * ( 1 byte) prime_delay = scalar, U08, 909, "sec", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 1 byte) fuelFreq = array , U08, 910, [ 2], "Hz", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 2 bytes) fuelFreq0 = scalar, U08, 910, "Hz", 1.00000, 0.00000, 0.00, 255, 0 fuelFreq1 = scalar, U08, 911, "Hz", 1.00000, 0.00000, 0.00, 255, 0 fuelCorr = array , U08, 912, [ 2], "%", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 2 bytes) fuelCorr0 = scalar, U08, 912, "%", 1.00000, 0.00000, 0.00, 255, 0 fuelCorr1 = scalar, U08, 913, "%", 1.00000, 0.00000, 0.00, 255, 0 AMCstep = scalar, U08, 914, "%", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 2 bytes) AMCdve = scalar, U08, 915, "%", 1.00000, 0.00000, 0.00, 255, 0 ; * ( 2 bytes) AMCve_rpm = scalar, U16, 916, "RPM", 1.00000, 0.00000, 0.00,15000.00, 0 ; * ( 2 bytes) AMCve_map = scalar, U16, 918, "kPa", 0.10000, 0.00000, 0.00, 300.00, 2 ; * ( 2 bytes) AMCramve_dt = scalar, U16, 920, "sec", 1.0, 0.0, 0.0, 300.0, 0 ; * ( 2 bytes) AMCT_thresh = scalar, U16, 922, "sec", 1.0, 0.0, 0.0, 1800.0, 0 ; * ( 2 bytes) AMCupdate_thresh= scalar, U16, 924, "events", 1.0, 0.0, 0.0, 30000.0, 0 ; * ( 2 bytes) CWOption = bits , U08, 926, [0:0], "Two-Point", "Table" ; * ( 1 byte ) knkOption = bits , U08, 927, [0:1], "Disabled", "Safe Mode", "Aggressive Mode", "INVALID" ; * ( 1 byte ) knkDirection = bits , U08, 927, [4:4], "Below threshold", "Above threshold" ; * knk_maxrtd = scalar, U08, 928, "deg", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_step1 = scalar, U08, 929, "deg", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_step2 = scalar, U08, 930, "deg", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_trtd = scalar, U08, 931, "sec", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_tadv = scalar, U08, 932, "sec", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_dtble_adv = scalar, U08, 933, "deg", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) knk_ndet = scalar, U08, 934, "knocks", 1.0, 0.0, 0.0, 255, 0 ; * ( 1 byte ) ;pad = scalar, U08, 935, knk_maxmap = scalar, U16, 936, "kPa", 0.1, 0.0, 0.0, 300.0, 1 ; * ( 2 bytes) knk_lorpm = scalar, U16, 938, "rpm", 1.0, 0.0, 0.0, 10000, 0 ; * ( 2 bytes) knk_hirpm = scalar, U16, 940, "rpm", 1.0, 0.0, 0.0, 10000, 0 ; * ( 2 bytes) knk_rpm = array , U16, 942, [ 6], "rpm", 1.0, 0.0, 0.0, 6000, 0 ; * ( 2 bytes) knk_thresh = array , U16, 954, [ 6], "v", 0.01, 0.0, 0.0, 5.00, 2 ; * ( 2 bytes) triggerTeeth = scalar, U16, 966, "teeth", 1.0, 0.0, 0.0, 512, 0 ; * ( 2 bytes) No_Miss_Teeth = scalar, U08, 968, "teeth", 1.0, 0.0, 0.0, 255, 0 ; * ( 1 byte ) No_Skip_Teeth = scalar, U08, 969, "teeth", 1.0, 0.0, 0.0, 255, 0 ; * ( 1 byte ) Delay_Teeth = scalar, U08, 970, "teeth", 1.0, 0.0, 0.0, 255, 0 ; * ( 1 byte ) ICISR_tmask = scalar, U08, 971, "msec", 0.1, 0.0, 0.0, 25.5, 1 ; * ( 1 byte ) ICISR_pmask = scalar, U08, 972, "%", 1.0, 0.0, 0.0, 200, 0 ; * ( 1 byte ) injTestMode = bits , U08, 973, [0:1], "Normal Mode", "Test Mode", "Repeat Test", "INVALID" ; ( 1 byte ) ae_lorpm = scalar, U16, 974, "rpm", 1.0, 0.0, 0.0, 10000, 0 ; * ( 2 bytes) ae_hirpm = scalar, U16, 976, "rpm", 1.0, 0.0, 0.0, 10000, 0 ; * ( 2 bytes) fuelSpkDel = array , S16, 978, [ 2], "deg", 0.10000, 0.00000,-45.00, 45.00, 1 ; * ( 4 bytes) fuelSpkDel0 = scalar, S16, 978, "deg", 0.10000, 0.00000,-45.00, 45.00, 1 fuelSpkDel1 = scalar, S16, 980, "deg", 0.10000, 0.00000,-45.00, 45.00, 1 injTestSqrts = scalar, U16, 982, "squirts", 1, 0, 0, 65000, 0 ; ( 2 bytes) injTestPW = scalar, U16, 984, "msec", 0.001, 0, 0, 65, 3 ; ( 2 bytes) injTestOffTime = scalar, U16, 986, "msec", 0.1, 0, 0, 6500, 1 ; ( 2 bytes) CID = scalar, U16, 988, "cu.in.", 1, 0, 0, 700, 1 ; ( 2 bytes) alpha = scalar, U08, 990, "%", 1.0, 0.0, 50, 150, 0 ; * ( 1 byte ) beta = scalar, U08, 991, "%", 1.0, 0.0, 0.0, 100, 0 ; * ( 1 byte ) gamma = scalar, U08, 992, "%", 1.0, 0.0, 0.0, 50, 0 ; * ( 1 byte ) acc_synchk = bits, U08, 993, [0:1], "Check Only at Steady Speed", "Check Accel and Steady Speed", "Check Decel and Steady Speed", "Check Always" ; (1 byte) ; pageSize = 994 page = 2 veTable1 = array , U08, 0, [12x12], "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * (144 bytes) veTable2 = array , U08, 144, [12x12], "%", 1.00000, 0.00000, 0.00, 255.00, 0 ; * (144 bytes) advanceTable = array , S16, 288, [12x12], "deg", 0.10000, 0.00000,-10.00, 90.00, 1 ; * (288 bytes) AMCNBurns = scalar, U16, 576, "burns", 1, 0, 0, 65000, 0 ; x ( 2 bytes) primePWTable = array , S16, 578, [ 10], "msec", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 20 bytes) crankPWTable = array , S16, 598, [ 10], "msec", 0.10000, 0.00000, 0.00, 65.00, 1 ; * ( 20 bytes) asePctTable = array , S16, 618, [ 10], "%", 1.00000, 0.00000, 0.00, 400.00, 0 ; * ( 2 bytes) aseCntTable = array , S16, 638, [ 10], "cycles", 1.00000, 0.00000, 0.00, 2500.00, 0 ; * ( 2 bytes) #if CELSIUS #if EXPANDED_CLT_TEMP matTemps = array , S16, 658, [ 6], "°C", 0.05555, -320.000,-40.00, 300.00, 1 ; * ( 12 bytes) #else matTemps = array , S16, 658, [ 6], "°C", 0.05555, -320.000,-40.00, 150.00, 1 ; * ( 12 bytes) #endif #else #if EXPANDED_CLT_TEMP matTemps = array , S16, 658, [ 6], "°F", 0.10000, 0.00000,-40.00, 600.00, 1 #else matTemps = array , S16, 658, [ 6], "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif #endif matRetard = array , U08, 670, [ 6], "deg", 0.10000, 0.00000, 0.00, 25.5, 1 ; * ( 6 bytes) xTauOption = bits , U08, 676, [0:1], "Off", "Accel/Decel Only", "Warm-up + Accel/Decel", "INVALID" ; * ( 1 byte ) spkN2O = scalar, U08, 677, "deg", 0.10000, 0.00000, 0.00, 25.5, 1 ; * ( 1 bytes) XAccTable = array, U16, 678, [ 5], "%", 0.10000, 0.00000, 5.00, 90, 1 ; * ( 10 bytes) TauAccTable = array, U16, 688, [ 5], "msec", 1.00000, 0.00000, 2.00, 20000, 0 ; * ( 10 bytes) XDecTable = array, U16, 698, [ 5], "%", 0.10000, 0.00000, 5.00, 90, 1 ; * ( 10 bytes) TauDecTable = array, U16, 708, [ 5], "msec", 1.00000, 0.00000, 2.00, 20000, 0 ; * ( 10 bytes) XTrpms = array, U16, 718, [ 5], "rpm", 1.00000, 0.00000, 0.00, 10000, 0 ; * ( 10 bytes) XClt = array, U16, 728, [ 10], "%", 1.00000, 0.00000, 0.00, 600, 0 ; * ( 20 bytes) TauClt = array, U16, 748, [ 10], "%", 1.00000, 0.00000, 0.00, 600, 0 ; * ( 20 bytes) ipada = array, S16, 768, [ 48],"", 1.00000, 0.00000, 0.00, 300, 0 ; * ( 96 bytes) ; Supplemental corrections for barometer and IAT. baroCorrVals = array , S16, 864, [ 6], "kPa", 0.10000, 0.00000, 80.0, 120.00, 1 ; * ( 24 bytes) #if CELSIUS #if EXPANDED_CLT_TEMP matCorrTemps = array , S16, 876, [ 6], "°C", 0.05555, -320.000,-40.00, 300.00, 1 ; * ( 12 bytes) #else matCorrTemps = array , S16, 876, [ 6], "°C", 0.05555, -320.000,-40.00, 150.00, 1 ; * ( 12 bytes) #endif #else #if EXPANDED_CLT_TEMP matCorrTemps = array , S16, 876, [ 6], "°F", 0.10000, 0.00000,-40.00, 600.00, 1 #else matCorrTemps = array , S16, 876, [ 6], "°F", 0.10000, 0.00000,-40.00, 300.00, 1 #endif #endif baroCorrDelta = array , S08, 888, [ 6], "%", 1.00000, 0.00000,-100.0, 120.0, 1 ; * ( 6 bytes) matCorrDelta = array , S08, 894, [ 6], "%", 1.00000, 0.00000,-100.0, 120.0, 1 ; * ( 6 bytes) MAFFlow = array , U16, 900, [ 12], "gram/sec", 0.01000, 0.00000, 0.00, 650.0, 1 ; * ( 24 bytes) MAFCor = array , U08, 924, [ 12], "%", 1.00000, 0.00000, 0.00, 255.0, 0 ; * ( 12 bytes) MAFRPM1 = scalar, U16, 936, "rpm", 1.00000, 0.00000, 0.00, 10000, 0 ; * ( 2 bytes) MAFRPM2 = scalar, U16, 938, "rpm", 1.00000, 0.00000, 0.00, 10000, 0 ; * ( 2 bytes) MAFDir = bits , U08, 940, [0:0], "Use Above", "Invert Above" ; * ( 1 byte ) VEIXOptn = bits , U08, 941, [0:0], "Use MAP only", "Adjust MAP for Baro" ; * ( 1 byte ) MatRtdRPMHi = scalar, U16, 942, "rpm", 1.00000, 0.00000, 0.00, 10000, 0 ; * ( 2 bytes) MatRtdRPMLo = scalar, U16, 944, "rpm", 1.00000, 0.00000, 0.00, 10000, 0 ; * ( 2 bytes) ; pageSize = 946 [Menu] ;---------------------------------------------------------------------------- ; There are five pre-defined values that may be used to define your menus. ; The first four allow access to the "standard" dialog boxes, the last one ; merely draws a separator (horizontal line) in the menu. ; ; std_constants ; std_enrichments ; std_realtime ; std_warmup ; std_accel ; ; std_separator ; ; Additionally, to support MegaSquirt-II firmware, there are two standard ; dialogs to generate its three embedded tables. The first of these acts ; like Roger Enns' EasyTherm, but only works for MS-II. The second one ; generates the internal AFR table required for proper closed loop operation ; in MS-II. Use these without page numbers, as they will just be ignored ; in any case. ; ; std_ms2gentherm ; std_ms2geno2 ; ; If you use any of the std_constants, std_enrichments or std_warmup ; editors, they may be optionally suffixed with a page number (only ; useful for multi-page code variants), which causes them to edit the ; specified page. If you leave off the page specifier, they edit logical ; page one as specified in the Constants section. ; ; There are four special menu names, which when used append to the standard ; menus of the same name instead of creating a new one. The menu names ; are "File", "Communications", "Tools" and "Help". ; ;---------------------------------------------------------------------------- menuDialog = main menu = "Fuel &Set-Up" subMenu = generalSettings, "&General" subMenu = idleControl, "I&dle Control", 0, { ECUType == 1 || ECUType == 2} subMenu = std_port_edit, "Spare &Port Settings", 0, { ECUType == 1 || ECUType == 2} subMenu = std_separator, ;---------------------------------------------- subMenu = injChars, "I&njector Characteristics", 0, { ECUType == 1 || ECUType == 2} subMenu = std_injection, "Injection &Control", 0, { ECUType == 1 || ECUType == 2} subMenu = revLimiter, "&Rev Limiter", 0, { ECUType == 1 || ECUType == 2} subMenu = aseSettings, "After&Start Enrichment" , 0, { ECUType == 1 || ECUType == 2} subMenu = accSettings, "Acce&l Enrichment Config", 0, { ECUType == 1 || ECUType == 2} subMenu = otherFuel, "&Other Fuel Settings", 0, { ECUType == 1 || ECUType == 2} subMenu = baroCorrection, "2-Point &Barometric Correction", 0, { ECUType == 1 || ECUType == 2} subMenu = flexFuelSettings,"&Flex Fuel", 0, { ECUType == 1 || ECUType == 2} subMenu = egoControl, "&EGO Control", 0, { ECUType == 1 || ECUType == 2} subMenu = amcSettings, "Automatic &Mixture Control", 0, { ECUType == 1 || ECUType == 2} subMenu = std_separator ;---------------------------------------------- subMenu = alphaNOptions, "&Alpha-N Blending", 0, { algorithm > 0 && (ECUType == 1 || ECUType == 2)} subMenu = MAFSettings, "MAP vrs. MAF &Usage", 0, { ECUType == 1 || ECUType == 2} menuDialog = main menu = "&Ignition Set-Up" subMenu = ignitionOptions, "&Base Ignition Settings", 0, { ECUType == 1 || ECUType == 2} subMenu = dwellSettings, "D&well Settings", 0, { ECUType == 1 || ECUType == 2} subMenu = AdvncdignitionOptions, "&Advanced Ignition Options",0, { ECUType == 1 || ECUType == 2} subMenu = knockThreshold, "&Knock Threshold", 0, { ECUType == 1 || ECUType == 2} menuDialog = knockThreshold menu = "&Settings" subMenu = knockSettings, "&Knock Sensor Settings", 0, { ECUType == 1 || ECUType == 2} menuDialog = main menu = "B&asic Tables" #if MAPbaro subMenu = std_separator ;---------------------------------------------- subMenu = veTable1Tbl, "&VE Table 1 (MAP/Baro)", 0, { MAFOption != 1 && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = afrTable1Tbl, "&AFR Table 1 (MAP/Baro)", 0, { egoType >= 3 && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = veTable2Tbl, "V&E Table 2 (MAP/baro)", 0, { MAFOption != 1 && dualTable && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = afrTable2Tbl, "AFR &Table 2 (MAP/Baro)", 0, { egoType >= 3 && dualTable && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = ignitionTbl, "&Spark Advance Table (MAP/Baro)",0, { VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} #else subMenu = veTable1Tbl, "VE Table &1 (MAP)", 0, { MAFOption != 1 && VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} subMenu = afrTable1Tbl, "A&FR Table 1 (MAP)", 0, { egoType >= 3 && VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} subMenu = veTable2Tbl, "VE Table &2 (MAP)", 0, { MAFOption != 1 && dualTable && VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} subMenu = afrTable2Tbl, "AF&R Table 2 (MAP)" 0, { egoType >= 3 && dualTable && VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} subMenu = ignitionTbl, "S&park Advance Table (MAP)", 0, { VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} #endif menuDialog = main menu = "Othe&r Tables" subMenu = tempTableBins, "&Temperature Table Values", 0, { ECUType == 1 || ECUType == 2} subMenu = alphaMAPTbl, "&Alpha-N MAP Table", 0, { algorithm > 0 && (ECUType == 1 || ECUType == 2)} subMenu = barometerCorr, "Barometric &Correction", 0, { CWOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = std_separator ;---------------------------------------------- subMenu = primingPW, "Pri&ming Pulse", 0, { CWOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = crankingPW, "Cra&nking Pulse", 0, { CWOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = asePct, "A&SE Percentage", 0, { CWOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = aseTaper, "AS&E Taper", 0, { CWOption > 0 && (ECUType == 1 || ECUType == 2)} menuDialog = veTable1Tbl menu = "&Edit Bins" subMenu = fmapTableBins, "Edit Fuel &MAP Bins" subMenu = frpmTableBins, "Edit Fuel &RPM Bins" menuDialog = veTable2Tbl menu = "&Edit Bins" subMenu = fmapTableBins, "Edit Fuel &MAP Bins" subMenu = frpmTableBins, "Edit Fuel &RPM Bins" menuDialog = ignitionTbl menu = "&Edit Bins" subMenu = smapTableBins, "Edit Spark &MAP Bins" subMenu = srpmTableBins, "Edit Spark &RPM Bins" menuDialog = main menu = "&Tuning" subMenu = std_realtime, "&Realtime Display", 0, { ECUType == 1 || ECUType == 2} #if MAPbaro subMenu = std_separator ;---------------------------------------------- subMenu = veTable1Map, "VE &Table 1 (MAP/Baro)", 0, { MAFOption != 1 && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = veTable2Map, "VE T&able 2 (MAP/Baro)", 0, { MAFOption != 1 && dualTable && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = afrTable1Map, "A&FR Ta&ble 1 (MAP/Baro)", 0, { egoType >= 3 && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = afrTable2Map, "A&FR Tabl&e 2 (MAP/Baro)", 0, { egoType >= 3 && dualTable && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} subMenu = ignitionMap, "I&gnition Advance Table (MAP/Baro)", 0, { VEIXOptn > 0 && VEIXOptn > 0 && (ECUType == 1 || ECUType == 2)} #else subMenu = std_separator ;---------------------------------------------- subMenu = veTable1Map, "VE Table &1 (MAP)", 0, { MAFOption != 1 && VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} subMenu = veTable2Map, "VE Table &2 (MAP)", 0, { MAFOption != 1 && dualTable && (ECUType == 1 || ECUType == 2)} subMenu = afrTable1Map, "A&FR Table 1 (MAP)", 0, { egoType >= 3 && VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} subMenu = afrTable2Map, "AF&R Table 2 (MAP)", 0, { egoType >= 3 && dualTable && VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} subMenu = ignitionMap, "&Spark Advance Table (MAP)", 0, { VEIXOptn == 0 && (ECUType == 1 || ECUType == 2)} #endif subMenu = std_separator ;---------------------------------------------- subMenu = std_warmup, "&Warmup Wizard", 0, { ECUType == 1 || ECUType == 2} subMenu = std_accel, "Acce&leration Wizard", 0, { ECUType == 1 || ECUType == 2} menuDialog = main menu = "X-Ta&u Tuning" subMenu = XAccTable, "Puddling Factors (&accel)", 0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = XDecTable, "Puddling Factors (&decel)", 0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = TauAccTable, "Time Factors (a&ccel)", 0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = TauDecTable, "Time Factors (d&ecel)", 0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = XCltTable, "&X (Puddling) Temp. Corrections",0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = TCltTable, "&Tau (Time) Temp. Corrections", 0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = std_separator ;---------------------------------------------- subMenu = xTauSettings, "&MAPdot Settings", 0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} subMenu = XTrpmsdial, "&RPM Values", 0, { xTauOption > 0 && (ECUType == 1 || ECUType == 2)} menuDialog = main menu = "Oth&er Tuning" subMenu = coldAdvance, "&Cold Advance", 0, { ECUType == 1 || ECUType == 2} subMenu = std_separator ;---------------------------------------------- subMenu = manifoldTempCorr,"I&AT-Based Fuel Correction", 0, { ECUType == 1 || ECUType == 2} subMenu = matBasedRetard, "IAT-&Based Timing Retard", 0, { ECUType == 1 || ECUType == 2} subMenu = std_separator ;---------------------------------------------- subMenu = iacSteps, "I&dle Steps", 0, { IdleCtl == 2 || IdleCtl == 3 || IdleCtl == 5 && (ECUType == 1 || ECUType == 2)} subMenu = ipwBins, "Idle &PWM Dutycycle", 0, { IdleCtl == 4 } subMenu = std_separator ;---------------------------------------------- subMenu = alphaMAPMap, "Alpha-&N MAP Table", 0, { algorithm > 0 && (ECUType == 1 || ECUType == 2)} subMenu = std_separator ;---------------------------------------------- subMenu = MAFtable1, "&MAF Correction Table", 0, { MAFOption > 0 && (ECUType == 1 || ECUType == 2)} menuDialog = main menu = "Tools" subMenu = std_ms2gentherm, "Calibrate T&hermistor Tables...",0, { ECUType == 1 || ECUType == 2} subMenu = std_ms2geno2, "Calibrate &AFR Table...", 0, { ECUType == 1 || ECUType == 2} subMenu = sensorCal, "&Sensor Calibration...", 0, { ECUType == 1 || ECUType == 2} subMenu = std_trigwiz, "Tri&gger Wizard...", 0, { ECUType == 1 || ECUType == 2} subMenu = injector_test, "&Injector Test Mode", 0, { ECUType == 1 || ECUType == 2} menu = "Help" subMenu = helpGeneral, "&MS-II Info" subMenu = sensorHelp, "&Sensor Calibration" subMenu = burnHelp, "&Burning Values to ECU" ;------------------------------------------------------------------------------- [UserDefined] dialog = generalSettings, "General Settings" topicHelp = "http://www.megamanual.com/mt28.htm#sg" field = "ECU Type", ECUType field = "!MUST set ECU Type before editting other values." field = "Engine displacement", CID, { ECUType == 1 || ECUType == 2} field = "Injection Timing Delay", InjStart, { ECUType == 1 || ECUType == 2} ; field = "#System" ; field = "Temperature Units", tempUnits, { ECUType == 1 || ECUType == 2} field = "Dual Table Use", dualTable, { ECUType == 1 || ECUType == 2} field = "Barometric Correction", baroCorr, { ECUType == 1 || ECUType == 2} # set X_TAU_VISIBLE #if X_TAU_VISIBLE field = "X-Tau Usage", xTauOption, { ECUType == 1 || ECUType == 2} #endif field = "Prime, ASE, WUE & Baro Tables", CWOption, { ECUType == 1 || ECUType == 2} field = "#Input Smoothing Factors" field = "MAP/MAF Averaging Lag Factor", mapLF, { ECUType == 1 || ECUType == 2} field = "RPM Averaging Lag Factor", rpmLF, { ECUType == 1 || ECUType == 2} field = "TPS Averaging Lag Factor", tpsLF, { ECUType == 1 || ECUType == 2} field = "Lambda Averaging Lag Factor", egoLF, { ECUType == 1 || ECUType == 2} field = "CLT/IAT/Battery Lag Factor", adcLF, { ECUType == 1 || ECUType == 2} field = "Knock Averaging Lag Factor", knkLF, { ECUType == 1 || ECUType == 2} field = "#Sampling Rates" field = "TPS Sample Rate", tpsdotSample, { ECUType == 1 || ECUType == 2} field = "MAP Sample Rate", mapdotSample, { ECUType == 1 || ECUType == 2} dialog = revLimiter, "Rev Limiter" topicHelp = "http://www.megamanual.com/mt28.htm#sr" field = "Algorithm", RevLimOption field = "Maximum Retard", RevLimMaxRtd, { RevLimOption == 1 } field = "Lower Rev Limit", RevLimRpm1 field = "Upper Rev Limit", RevLimRpm2 dialog = flexFuelSettings, "Flex Fuel Settings" topicHelp = "http://www.megamanual.com/mt28.htm#sf" field = "Flex Fuel Sensor", flexFuel field = "Frequency (low)", fuelFreq0, { flexFuel > 0 } field = "Fuel Correction (low)", fuelCorr0, { flexFuel > 0 } field = "Timing Correction (low)", fuelSpkDel0, { flexFuel > 0 } field = "Frequency (high)", fuelFreq1, { flexFuel > 0 } field = "Fuel Correction (high)", fuelCorr1, { flexFuel > 0 } field = "Timing Correction (high)", fuelSpkDel1, { flexFuel > 0 } dialog = otherFuel, "Other Fuel Settings" topicHelp = "http://www.megamanual.com/mt28.htm#so" field = "#Engine Start Up" field = "Max. Cranking Speed", crankingRPM, { 1 } field = "TPS for Flood Clear Mode", floodClear field = "#VE Table Adjustments" field = "(May have to save MSQ and reload to get to stick)" field = "Use MAP/baro for tables", VEIXOptn, { 1 } field = " - Must also set/unset MAPbaro in settings.ini -" field = "AFR Table Fuel Calc Usage", AFRMult, { 1 } field = "AFR Stioch. Ratio", AFRStoichNB, { AFRMult == 1 } field = "AFR Stioch. Ratio", AFRStoichWB, { AFRMult == 2 } field = "#Two-Point Prime" field = "Prime Pulse Cold PW", primePulseCold, { CWOption == 0 } field = "Prime Pulse Hot PW", primePulseHot, { CWOption == 0 } field = "Prime Delay", prime_delay field = "#Additional Fuel (switched by E0 low or cyclic)" #if n2o field = "Nitrous Oxide Enrichment", n2oEnrich field = "Spark Retard When N2O Active", spkN2O #else field = "Fuel Added to Base PW", pwImpulse field = "#Additional Fuel (cyclic only)" field = "Time Between Added Fuel", impulseSec field = "Number of Cycles", nImpulse #endif dialog = aseSettings, "AfterStart Enrichment Settings" topicHelp = "http://www.megamanual.com/mt28.htm#ss" field = "#Hot AfterStart Enrichment" field = "ASE Hot Start Enable", ASEHot field = "#Two-Point AfterStart Enrich" field = "ASE Cold Percent", asePctCold, { CWOption == 0 } field = "ASE Hot Percent", asePctHot, { CWOption == 0 } field = "ASE Cold Count", aseCountCold, { CWOption == 0 } field = "ASE Hot Count", aseCountHot, { CWOption == 0 } dialog = accSettings, "Accel Enrichment Configuration" topicHelp = "http://www.megamanual.com/mt28.htm#sl" field = "#AE RPM Scaling (for non-XTau accel)" field = "Low RPM Threshold", ae_lorpm, field = "High RPM Threshold", ae_hirpm, dialog = baroCorrection, "2-Point Barometric Correction" topicHelp = "http://www.megamanual.com/mt28.htm#sb" field = "#Barometric Correction" field = "At total vacuum ", bcor0 field = "Rate", bcormult dialog = xTauSettings, "X-Tau MAPdot Settings" topicHelp = "http://www.megamanual.com/mt28.htm#um" field = "#MAPdot Thresholds for transition to X, Tau Decel Tables" field = "Start Transition", MapThreshXTD field = "Finish Transition", MapThreshXTD2 field = "#" field = "#MAPdot trending threshhold is the start of" field = "#Map Trending for faster AE/ XTau enrichment" field = "MAPdot Trending Threshhold", MapThreshXTA field = "Max. MAP added per sample", trendmapLimit dialog = injChars, "Injector Characteristics" topicHelp = "http://www.megamanual.com/mt28.htm#sn" field = "Injector Open Time", injOpen field = "Battery Voltage Correction", battFac field = "PWM Current Limit", injPwmP field = "PWM Time Threshold", injPwmT field = "!Injector PWM Period", injPwmPd ; ! field = "!Red settings require an MS-II reboot!" dialog = egoControl, "EGO Control" topicHelp = "http://www.megamanual.com/mt28.htm#se" field = "EGO Sensor Type", egoType #if NARROW_BAND_EGO field = "NB Voltage Target", egoTarget, { egoType == 1 || egoType == 2} #elif LAMBDA field = "NB Lambda Target", AFRTarget, { egoType == 1 || egoType == 2} #else field = "NB AFR Target", AFRTarget, { egoType == 1 || egoType == 2} #endif field = "Ignition Events per Step", egoCount, { egoType == 1 || egoType == 2 || egoType > 2 && egoAlgorithm == 0} field = "Controller Step Size", egoDelta, { egoType == 1 || egoType == 2} field = "Controller Authority ±", egoLimit, { egoType > 0 } field = "Active Above Coolant Temp", egoTemp, { egoType > 0 } field = "Active Above RPM", egoRPM, { egoType > 0 } field = "Active Below TPS", TPSOXLimit, { egoType > 0 } field = "Active Below MAP", MAPOXLimit, { egoType > 0 } field = "#WB Controller Settings" field = "Algorithm", egoAlgorithm, { egoType > 2 } field = "PID Proportional Gain", egoKP, { egoType > 2 } field = "Transport Delay 1", egoKdelay1, { egoType > 2 && egoAlgorithm > 0 } field = "Transport Delay 2", egoKdelay2, { egoType > 2 && egoAlgorithm > 0 } field = "PID Integral", egoKI, { egoType > 2 && egoAlgorithm > 1 } field = "PID Derivative", egoKD, { egoType > 2 && egoAlgorithm > 1 } dialog = amcSettings, "Automatic Mixture Control" topicHelp = "http://www.megamanual.com/mt28.htm#sm" field = "!Must have EGO correction enabled for AMC to operate!" field = "Automatic Mixture Control", AMCOption, { egoType > 0 } field = "Step size", AMCstep, { AMCOption > 0 } field = "Minimum VE Change", AMCdve, { AMCOption > 0 } field = "Vertex Tolerance", AMCve_rpm, { AMCOption > 0 } field = "Vertex Tolerance", AMCve_map, { AMCOption > 0 } field = "Table Change Interval", AMCramve_dt, { AMCOption > 0 } field = "Flash Update Interval", AMCT_thresh, { AMCOption > 1 } field = "Update After", AMCupdate_thresh, { AMCOption > 1 } dialog = alphaNOptions, "Alpha-N Blending" topicHelp = "http://www.megamanual.com/mt28.htm#sa" field = "Pure AN to Blend Threshold", alpha_lorpm field = "Blend to SD Threshold", alpha_hirpm field = "Baro Spark Advance (< 100kPa)", alpha_baro_spkadv dialog = ignitionOptions, "Base Ignition Settings" topicHelp = "http://www.megamanual.com/mt28.htm#ib" field = "#General Ignition" field = "Trigger Offset", triggerOffset field = "Skip Pulses", no_skip_pulses field = "#Prediction Settings", field = "Predictor Algorithm", PredOpt field = "Alpha", alpha, { PredOpt == 1 } field = "Beta", beta, { PredOpt == 1 } field = "Gamma", gamma, { PredOpt == 1 } field = "#Tach Signal Masking" field = "Time Mask", ICISR_tmask field = "Percentage Mask", ICISR_pmask field = "#Next-Pulse Tolerance" field = " Cranking", crankTolerance field = " After-start", asTolerance field = " Normal Running", pulseTolerance field = "Check Tach Sync Options", acc_synchk, { triggerTeeth == 0 } field = "!Ignition Input Capture", ICIgnCapture, { ICIgnOption != 2 && ICIgnOption != 3 } ; ! field = "!Cranking Trigger", ICCrankTrigger, { ICIgnOption != 2 && ICIgnOption != 3 } ; ! field = "!Coil Charging Scheme", ICIgnOption ; ! field = "!Spark Output", spkout_hi_lo ; ! dialog = AdvncdignitionOptions, "Advanced Ignition Options" topicHelp = "http://www.megamanual.com/mt28.htm#ia" field = "#Trigger Wheel Only (0 is no trigger wheel)" field = "#Set only with ENGINE OFF" field = "!Trigger Wheel Teeth", triggerTeeth field = "!Missing Teeth", No_Miss_Teeth, { triggerTeeth > 0 } field = "!Skip Teeth", No_Skip_Teeth, { triggerTeeth > 0 } field = "!Delay Teeth", Delay_Teeth, { triggerTeeth > 0 } field = "#Dual Spark Ignition Options" field = "!Dual Spark Options", DualSpkOptn field = "Offset (advance) for Output #2", OddAng field = "#IAT-based Spark Retard Limiting Options" field = "Start IAT Retard ", MatRtdRPMLo field = "Full IAT Retard ", MatRtdRPMHi field = "#Signal Delay Parameters" field = "FET Ouput Delay", fet_delay field = "VR Input Delay", vr_delay field = "!Red settings require an MS-II reboot!" dialog = dwellSettings, "Dwell Settings" topicHelp = "http://www.megamanual.com/mt28.htm#iw" field = "Maximum Dwell Duration", max_coil_dur field = "Maximum Spark Duration", max_spk_dur field = "Acceleration Compensation", dwellAcc field = "#Battery Voltage Compensation" ; Make this an array2D when available. array1D = "", "Voltage %INDEX% ", dwellVolts array1D = "", "Duration at Voltage %INDEX% ", dwellDuration dialog = idleControl, "Idle Control" topicHelp = "http://www.megamanual.com/mt28.htm#sd" field = "Algorithm", IdleCtl field = "Fast Idle Temperature", fastIdleT, { IdleCtl == 1 } field = "Time Step Size", IACtstep, { IdleCtl == 2 || IdleCtl == 3 || IdleCtl == 5 } field = "Acceleration Step Size", IACaccstep, { IdleCtl == 2 || IdleCtl == 3 || IdleCtl == 5 } field = "Minimum # steps to move", IACminstep, { IdleCtl == 2 || IdleCtl == 3 || IdleCtl == 5 } field = "!PWM Frequency", IACpwm_step, { IdleCtl == 4 } field = "!Start Value (retract)", IACStart, { IdleCtl > 1 } ; ! field = "Cranking Position (extend)", IACcrankpos, { IdleCtl > 1 } field = "Crank-to-Run Taper Time", IACcrankxt, { IdleCtl > 1 } field = "Hysteresis", IdleHyst, { IdleCtl >= 1 } field = "#Time-Based After Start (extended warm-up)" field = " Cold Temperature", IACcoldtmp, { IdleCtl > 1 } field = " Cold Position", IACcoldpos, { IdleCtl > 1 } field = " Cold Taper Time", IACcoldxt, { IdleCtl > 1 } dialog = sensorCal, "Sensor Calibration" topicHelp = sensorHelp field = "#MAP Sensor (F1 for common values)" field = "Value at 0.0 volts", map0 field = "Value at 5.0 volts", mapmax field = "#Barometer Sensor (usually identical to MAP)" field = "Value at 0.0 volts", baro0 field = "Value at 5.0 volts", baromax dialog = knockSettings, "Knock Sensor Settings" topicHelp = "http://www.megamanual.com/mt28.htm#ik" field = "Knock Control", knkOption field = "#Detection" field = "Threshold Direction", knkDirection, { knkOption > 0 } field = "Threshold", knock0 field = "Peak", knockmax field = "Knock Count", knk_ndet, { knkOption > 0 } field = "No Knock Above MAP", knk_maxmap, { knkOption > 0 } field = "No Knock Below RPM", knk_lorpm, { knkOption > 0 } field = "No Knock Above RPM", knk_hirpm, { knkOption > 0 } field = "#Retarding" field = "Maximum Retard", knk_maxrtd, { knkOption > 0 } field = "Retard Check Time", knk_trtd, { knkOption > 0 } field = "Retard Step Size", knk_step1, { knkOption > 0 } field = "#Recovery" field = "Advance Check Time", knk_tadv, { knkOption > 0 } field = "Advance Step Size", knk_step2, { knkOption > 0 } field = "Recovery Advance", knk_dtble_adv, { knkOption > 1 } dialog = injector_test, "Injector Test Mode" topicHelp = "http://www.megamanual.com/mt28.htm#oi" field = "!Injector test mode", injTestMode ; ! field = "Injector test squirts", injTestSqrts, { injTestMode > 0 } field = "Injector test PW", injTestPW, { injTestMode > 0 } field = "Injector test offtime", injTestOffTime, { injTestMode > 0 } field = "!Reboot to test, set to 'Normal Mode' to reset" dialog = frpmTableBins, "RPM Table Bins for Fuel Tables" topicHelp="http://www.megamanual.com/mt28.htm#" array1D = "", "Fuel RPM %INDEX% ", frpm_table field = "#Close and re-open Table(s) to see changes" dialog = fmapTableBins, "MAP Table Bins for Fuel Table(s)" topicHelp="http://www.megamanual.com/mt28.htm#" array1D = "", "Fuel MAP %INDEX% ", fmap_table field = "#Close and re-open Table(s) to see changes" dialog = srpmTableBins, "RPM Table Bins for Spark Table" topicHelp="http://www.megamanual.com/mt28.htm#" array1D = "", "Spark RPM %INDEX% ", srpm_table field = "#Close and re-open Table(s) to see changes" dialog = smapTableBins, "MAP Table Bins for Spark Table" topicHelp="http://www.megamanual.com/mt28.htm#" array1D = "", "Spark MAP %INDEX% ", smap_table field = "#Close and re-open Table(s) to see changes" dialog = tempTableBins, "Temperature Table Values" topicHelp="http://www.megamanual.com/mt28.htm#at" array1D = "", "Temperature %INDEX% ", tempTable dialog = XtempTableBins, "X Temperature Correction Values" topicHelp="http://www.megamanual.com/mt28.htm#at" field = "#Temperature Correction for X Enrichments" array1D = "", "Correction %INDEX% ", XClt dialog = TtempTableBins, "Tau Temperature Correction Values" topicHelp="http://www.megamanual.com/mt28.htm#at" array1D = "", "Correction %INDEX% ", TauClt dialog = XTrpmsdial, "X-Tau RPM Values" topicHelp="http://www.megamanual.com/mt28.htm#ur" field = "#RPM Bins for X-Tau Enrichments" array1D = "", "X-Tau RPM %INDEX% ", XTrpms dialog = MAFSettings, "MAF vrs. MAP Usage" topicHelp = "http://www.megamanual.com/mt28.htm#su" field = "#See Tables for MAF flow setting" field = "Enable MAF Use", MAFOption field = "MAF Hardware Configuration", MAFpin, { MAFOption > 0 } field = "Note: MAF must NOT be on MAP pin for MAF/MAP blend." field = "#MAP MAF Blend Settings" field = "MAP Only Above RPM", MAFRPM1, { MAFOption > 1 } field = "MAF Only Below RPM", MAFRPM2, { MAFOption > 1 } field = "Invert above MAP/MAF settings", MAFDir, { MAFOption > 1 } field = "#Viewing MAF in Real Time" field = "You can set one of the gauges on the front page to mafGauge" field = "to see the MAF in real time. Right click on any gauge and" field = "select mafGuage " help = burnHelp, "Burning Values to ECU" webHelp = "http://www.megamanual.com/mt28.htm" text = "Occassionally, you may have trouble getting values to 'stick'" text = "in MegaTune. There are a few things you can try if this happens:

" text = "\tHit TAB after entering the value. This forces MegaTune to" text = "recognize the changed value.
" text = "\tThen 'Burn to ECU'

" text = "If that doesn't work:

" text = "\tChange the value (as above) and immediately save the MSQ file ('File/Save').
" text = "\tThen reload the file you just saved, and burn it when prompted.

" text = "This forces all the values to be burned to both flash and RAM memory, and" text = "should solve the problem." help = sensorHelp, "Sensor Calibration" webHelp = "http://www.megamanual.com/mt28.htm#os" text = "MAP Sensor Calibration
" text = "
" text = "For the\tMPX4115 use\t10.6 and \t121.7
" text = "\tMPX4250\t\t10.0\t260.0
" text = "\tMPXH6300\t1.1\t315.5
" text = "\tGM 3-BAR\t1.1\t315.5
" text = "\tMPXH6400\t3.5\t416.5
" text = "
" text = "(GM 3-bar data from Dave Hartnell, http://www.not2fast.com/electronics/component_docs/MAP_12223861.pdf)
" text = "
" text = "\tSensor type\tvLo\tpLo\tvHi\tpHi\tvRef
" text = "\tMPX4115 \t0.204 v\t15 kPa\t4.794 v\t115 kPa\t5.100 v
" text = "\tMPX4250 \t0.204 v\t20 kPa\t4.896 v\t250 kPa\t5.100 v
" text = "\tMPXH6300\t0.306 v\t20 kPa\t4.913 v\t304 kPa\t5.100 v
" text = "\tGM 3-BAR\t0.631 v\t40 kPa\t4.914 v\t304 kPa\t5.100 v
" text = "\tMPXH6400\t0.200 v\t20 kPa\t4.800 v\t400 kPa\t5.000 v
" text = "
" text = "In general, use values derived from these equations:
" text = "
" text = "\tm = (pHi-pLo)/(vHi-vLo)
" text = "\tpv1 = pLo - m * vLo
" text = "\tpv2 = pv1 + m * vRef
" text = "
" text = "References:
" text = "\thttp://www.freescale.com/files/sensors/doc/data_sheet/MPX4115A.pdf
" text = "\thttp://www.freescale.com/files/sensors/doc/data_sheet/MPX4250A.pdf
" text = "\thttp://www.freescale.com/files/sensors/doc/data_sheet/MPXH6300A.pdf
" text = "\thttp://www.freescale.com/files/sensors/doc/data_sheet/MPXH6400A.pdf
" text = "
" text = "Barometer Sensor Calibration
" text = "
" text = "If your system has an external barometer sensor, separate from the MAP" text = "sensor, then use these values to calibrate it properly. If you have" text = "a standard MS installation, then copy your MAP sensor values here.
" text = "
" text = "Barometric Correction Calibration
" text = "
" text = "Correction for barometric effects is performed using the linear function below.
" text = "
" text = "\tcorrection = correction_0 + (rate * barometer) / 100
" text = "
" text = "'At total vacuum' contains the total correction at a barometer reading" text = "of 0 kPa (you are on the moon). The 'Rate' contains the percentage per 100" text = "kPa to scale the barometer value. Using the default values of 147 and -47," text = "we see that for a barometer of 100 kPa, we have 100% correction.
" text = "
" text = "\tcorrection = 147 + (-47*100) / 100 = 100%" help = helpGeneral, "MS-II General Help" webHelp = "http://www.megamanual.com/mt28.htm" text = "Al Grippo and Bruce Bowling have created MegaSquirt-II, which" text = "is a plug-in daughter card that replaces the 8-bit MC68HC908GP32" text = "with a 16-bit MC9S12C64 processor. MegaSquirt-II is an intermediate" text = "step from the original MegaSquirt towards UltraMegaSquirt.
" text = "
" text = "It is basically a plug-in processor card that has the MC9S12C64" text = "processor plus support hardware as well as a stepper motor chip," text = "and an ignition module controller. The embedded code is written" text = "in C, rather than assembly language, so it should be more accessible" text = "to more programmers (Stephane Carrez has ported GCC to the HC12" text = "processor so, although it doesn't use the full 9S12 instruction" text = "set, we are able to use his version to write code for the MS-II).
" text = "
" text = "For current documentation, click the Web Help button below, or for" text = "support questions visit http://www.msefi.com/." ;------------------------------------------------------------------------------- [CurveEditor] curve = coldAdvance, "Cold Ignition Advance Offset" topicHelp = "http://www.megamanual.com/mt28.htm#ec" columnLabel = "Coolant", "Offset" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = -10, 10, 5 xBins = tempTable, coolant yBins = cold_adv_table gauge = cltGauge curve = iacSteps, "IAC Steps" topicHelp = "http://www.megamanual.com/mt28.htm#ed" columnLabel = "Coolant", "IAC Steps" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 300, 7 xBins = tempTable, coolant yBins = iacstepTable gauge = cltGauge curve = ipwBins, "PWM Idle Duty Cycle" topicHelp = "http://www.megamanual.com/mt28.htm#ep" columnLabel = "Coolant", "Idle PWM" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 100, 6 xBins = tempTable, coolant yBins = ipwmTable gauge = cltGauge curve = primingPW, "Priming Pulsewidth" topicHelp = "http://www.megamanual.com/mt28.htm#rm" columnLabel = "Coolant", "Prime PW" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 20, 5 xBins = tempTable, coolant yBins = primePWTable gauge = cltGauge curve = crankingPW, "Cranking Pulsewidth" topicHelp = "http://www.megamanual.com/mt28.htm#rn" columnLabel = "Coolant", "Cranking PW" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 20, 5 xBins = tempTable, coolant yBins = crankPWTable gauge = cltGauge curve = asePct, "Afterstart Enrichment Percentage" topicHelp = "http://www.megamanual.com/mt28.htm#rs" columnLabel = "Coolant", "Afterstart" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 100, 6 xBins = tempTable, coolant yBins = asePctTable gauge = cltGauge curve = aseTaper, "Afterstart Enrichment Taper" topicHelp = "http://www.megamanual.com/mt28.htm#re" columnLabel = "Coolant", "Taper" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 500, 6 xBins = tempTable, coolant yBins = aseCntTable gauge = cltGauge curve = matBasedRetard, "IAT-Based Spark Timing Retard" topicHelp = "http://www.megamanual.com/mt28.htm#eb" columnLabel = "IAT", "Retard" xAxis = 100, 300, 9 yAxis = 0, 15, 7 xBins = matTemps, mat yBins = matRetard gauge = matGauge curve = knockThreshold, "Knock Threshold" topicHelp = "http://www.megamanual.com/mt28.htm#ik" columnLabel = "RPM", "Threshold" xAxis = 0, 6000, 7 yAxis = 0, 5.0, 6 xBins = knk_rpm, rpm yBins = knk_thresh gauge = tachometer curve = barometerCorr, "Non-Linear Barometric Correction" topicHelp = "http://www.megamanual.com/mt28.htm#rc" columnLabel = "Barometer", "Correction" xAxis = 60, 120, 7 yAxis = -30, 30, 7 xBins = baroCorrVals, barometer yBins = baroCorrDelta gauge = barometerGauge curve = manifoldTempCorr, "Non-Linear IAT (intake air temperature) Fuel Correction" topicHelp = "http://www.megamanual.com/mt28.htm#ea" columnLabel = "IAT", "Correction" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = -30, 30, 7 xBins = matCorrTemps, mat yBins = matCorrDelta gauge = matGauge curve = XAccTable, "X Accel Fuel Correction" topicHelp = "http://www.megamanual.com/mt28.htm#ua" columnLabel = "RPM", "Correction" xAxis = 0, 8000, 4 yAxis = 0, 120, 4 xBins = XTrpms, rpm yBins = XAccTable gauge = xTauGauge1 curve = XDecTable, "X Decel Fuel Correction" topicHelp = "http://www.megamanual.com/mt28.htm#ud" columnLabel = "RPM", "Correction" xAxis = 0, 8000, 9 yAxis = 0, 120, 9 xBins = XTrpms, rpm yBins = XDecTable gauge = xTauGauge1 curve = TauAccTable, "Tau Accel Fuel Correction" topicHelp = "http://www.megamanual.com/mt28.htm#uc" columnLabel = "RPM", "time" xAxis = 0, 8000, 9 yAxis = 0, 1000, 9 xBins = XTrpms, rpm yBins = TauAccTable gauge = xTauGauge1 curve = TauDecTable, "Tau Decel Correction" topicHelp = "http://www.megamanual.com/mt28.htm#ue" columnLabel = "RPM", "time" xAxis = 0, 8000, 9 yAxis = 0, 1000, 9 xBins = XTrpms, rpm yBins = TauDecTable gauge = xTauGauge1 curve = XCltTable, "X (Puddling) Temp. Correction Factors" topicHelp = "http://www.megamanual.com/mt28.htm#ux" columnLabel = "Temperature", "Correction" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 600, 9 xBins = tempTable yBins = XClt gauge = cltGauge curve = TCltTable, "Tau (Time) Temp. Correction Factors" topicHelp = "http://www.megamanual.com/mt28.htm#ut" columnLabel = "Temperature", "time" #if EXPANDED_CLT_TEMP xAxis = -40, 600, 9 #else xAxis = -40, 250, 9 #endif yAxis = 0, 600, 9 xBins = tempTable yBins = TauClt gauge = cltGauge curve = MAFtable1, "MAF Correction Table (to alter default MAF curve)" topicHelp = "http://www.megamanual.com/mt28.htm#em" columnLabel = "MAF Flow", "Correction" xAxis = 0, 300, 11 yAxis = 0, 255, 11 xBins = MAFFlow, maf yBins = MAFCor gauge = mafGauge [TableEditor] #if MAPbaro table = veTable1Tbl, veTable1Map, "VE Table 1 (MAP/baro)", 2 topicHelp = "http://www.megamanual.com/mt28.htm#a1" ; constant, variable xBins = frpm_table, rpm, readonly yBins = fmap_table, kpaix, readonly zBins = veTable1 upDownLabel = "RICHER", "LEANER" gridHeight = 2.0 gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = veTable2Tbl, veTable2Map, "VE Table 2", 2 topicHelp = "http://www.megamanual.com/mt28.htm#a1" xBins = frpm_table, rpm, readonly yBins = fmap_table, kpaix, readonly zBins = veTable2 upDownLabel = "RICHER", "LEANER" gridHeight = 2.0 gridOrient = 250, 0, 340 #else ; table_id, map3d_id, "title", page table = veTable1Tbl, veTable1Map, "VE Table 1 (MAP)", 2 topicHelp = "http://www.megamanual.com/mt28.htm#a1" ; constant, variable xBins = frpm_table, rpm, readonly yBins = fmap_table, calcMAP, readonly zBins = veTable1 upDownLabel = "RICHER", "LEANER" gridHeight = 2.0 gridOrient = 250, 0, 340 ; Space 123 rotation of grid in degrees. table = veTable2Tbl, veTable2Map, "VE Table 2", 2 topicHelp = "http://www.megamanual.com/mt28.htm#a1" xBins = frpm_table, rpm, readonly yBins = fmap_table, calcMAP, readonly zBins = veTable2 upDownLabel = "RICHER", "LEANER" gridHeight = 2.0 gridOrient = 250, 0, 340 #endif #if LAMBDA table = afrTable1Tbl, afrTable1Map, "Lambda Table 1", 1 gridHeight = 3.0 #else table = afrTable1Tbl, afrTable1Map, "AFR Table 1", 1 gridHeight = 1.0 #endif topicHelp = "http://www.megamanual.com/mt28.htm#af" xBins = frpm_table, rpm, readonly yBins = fmap_table, calcMAP, readonly zBins = afrTable1 upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 #if LAMBDA table = afrTable1Tblix, afrTable1MapIX, "Lambda Table 1", 1 gridHeight = 3.0 #else table = afrTable1Tblix, afrTable1MapIX, "AFR Table 1", 1 gridHeight = 1.0 #endif topicHelp = "http://www.megamanual.com/mt28.htm#af" xBins = frpm_table, rpm, readonly yBins = fmap_table, kpaix, readonly zBins = afrTable1 upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 #if LAMBDA table = afrTable2Tbl, afrTable2Map, "Lambda Table 2", 1 gridHeight = 3.0 #else table = afrTable2Tbl, afrTable2Map, "AFR Table 2", 1 gridHeight = 1.0 #endif topicHelp = "http://www.megamanual.com/mt28.htm#af" xBins = frpm_table, rpm, readonly yBins = fmap_table, calcMAP, readonly zBins = afrTable2 upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 #if LAMBDA table = afrTable2Tblix, afrTable2MapIX, "Lambda Table 2", 1 gridHeight = 3.0 #else table = afrTable2Tblix, afrTable2MapIX, "AFR Table 2", 1 gridHeight = 1.0 #endif topicHelp = "http://www.megamanual.com/mt28.htm#af" xBins = frpm_table, rpm, readonly yBins = fmap_table, kpaix, readonly zBins = afrTable2 upDownLabel = "LEANER", "RICHER" gridOrient = 250, 0, 340 #if MAPbaro table = ignitionTbl, ignitionMap, "Spark Advance Table", 2 topicHelp = "http://www.megamanual.com/mt28.htm#ap" xBins = srpm_table, rpm, readonly yBins = smap_table, kpaix, readonly zBins = advanceTable upDownLabel = "ADVANCING", "RETARDING" gridHeight = 3.0 gridOrient = 250, 0, 340 #else table = ignitionTbl, ignitionMap, "Spark Advance Table", 2 topicHelp = "http://www.megamanual.com/mt28.htm#ap" xBins = srpm_table, rpm, readonly yBins = smap_table, calcMAP, readonly zBins = advanceTable upDownLabel = "ADVANCING", "RETARDING" gridHeight = 3.0 gridOrient = 250, 0, 340 #endif table = alphaMAPTbl, alphaMAPMap, "Alpha-N MAP Table", 1 topicHelp = "http://www.megamanual.com/mt28.htm#en" xBins = amap_rpm, rpm yBins = amap_tps, tps zBins = alphaMAPtable upDownLabel = "UP", "DOWN" gridHeight = 2.0 gridOrient = 250, 0, 340 ;------------------------------------------------------------------------------- [GaugeConfigurations] ;------------------------------------------------------------------------------- ; Notes on some of the gauges. ; ; The accelEnrichGauge is now a composite of both acceleration enrichment ; and deceleration enleanment numbers. See the definition of the variable ; accDecEnrich in the OutputChannels section. ; ; David Hooke contributed the lambda gauge and associated transfer ; function files. ; ; The lambda gauge is the best way (my opinion) to report data from a ; wide band EGO gauge, it standardizes the output irrespective of fuel ; or mix of fuels, so you needn't do any brainwork to know if your 75% ; gasoline and 25% methanol is rich at 10:1 or not. ; ; Use the file WBlambda100AVR.inc, if using a standard ADC (e.g., AVR cpu). ; Use the file WBlambda100MOT.inc, if using a biased ADC (e.g., MOT cpu). ;------------------------------------------------------------------------------- ; Define a gauge's characteristics here, then go to a specific layout ; block (Tuning or FrontPage) and use the name you've defined here to ; display that gauge in a particular position. ; ; Name = Case-sensitive, user-defined name for this gauge configuration. ; Var = Case-sensitive name of variable to be displayed, see the ; OutputChannels block in this file for possible values. ; Title = Title displayed at the top of the gauge. ; Units = Units displayed below value on gauge. ; Lo = Lower scale limit of gauge. ; Hi = Upper scale limit of gauge. ; LoD = Lower limit at which danger color is used for gauge background. ; LoW = Lower limit at which warning color is used. ; HiW = Upper limit at which warning color is used. ; HiD = Upper limit at which danger color is used. ; vd = Decimal places in displayed value ; ld = Label decimal places for display of Lo and Hi, above. ;Name Var Title Units Lo Hi LoD LoW HiW HiD vd ld advBucketGauge = veTuneValue, "Advance Bucket", "degrees", 0, 55, -1, -1, 999, 999, 1, 1 advdegGauge = advance, "Ignition Advance", "degrees", 5, 50, -1, -1, 999, 999, 1, 1 IACgauge = iacstep, "IAC position", "steps", 0, 255, -1, -1, 999, 999, 0, 0 dwellGauge = dwell, "Dwell", "mSec", 0, 10, 0.5, 1.0, 6.0, 8.0, 1, 1 ; IAC step == idle pwm, when using pwm idle control. PWMIdlegauge = idleDC, "Idle PWM%", "%", 0, 100, -1, -1, 999, 90, 0, 0 accelEnrichGauge = accDecEnrich, "Accel Enrich", "%", 50, 150, -1, -1, 999, 999, 0, 0 afr1Gauge = afr1, "Air:Fuel Ratio", "", 10, 19.4, 12, 13, 15, 16, 2, 2 afr2Gauge = afr2, "Air:Fuel Ratio 2", "", 10, 19.4, 12, 13, 15, 16, 2, 2 clockGauge = seconds, "Clock", "Seconds", 0, 255, 10, 10, 245, 245, 0, 0 deadGauge = deadValue, "---", "", 0, 1, -1, -1, 2, 2, 0, 0 dutyCycle1Gauge = dutyCycle1, "Duty Cycle 1", "%", 0, 100, -1, -1, 85, 90, 1, 1 dutyCycle2Gauge = dutyCycle2, "Duty Cycle 2", "%", 0, 100, -1, -1, 85, 90, 1, 1 egoCorrGauge = egoCorrection, "EGO Correction", "%", 50, 150, 90, 99, 101, 110, 0, 0 egoCorrGauge1 = egoCorrection1,"EGO Correction 1", "%", 50, 150, 90, 99, 101, 110, 0, 0 egoCorrGauge2 = egoCorrection2,"EGO Correction 2", "%", 50, 150, 90, 99, 101, 110, 0, 0 egoGauge = egoVoltage, "Exhaust Gas Oxygen", "volts", 0, 1.0, 0.2, 0.3, 0.7, 0.8, 2, 2 kpabaroGauge = kpaix, "Engine MAP/baro", "kPa", 0, 255, 0, 20, 200, 245, 1, 0 knockGauge = knockRetard "Knock Retard", "deg", 0, 25.0, -1, -1, 5.0, 10.0, 1, 1 lambda1Gauge = lambda1, "Lambda", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 lambda2Gauge = lambda2, "Lambda", "", 0.5, 1.5, 0.5, 0.7, 2, 1.1, 2, 2 gammaEnrichGauge = gammaEnrich, "Gamma Enrichment", "%", 50, 150, -1, -1, 151, 151, 0, 0 mapGauge = map, "Engine MAP", "kPa", 0, 255, 0, 20, 200, 245, 1, 0 mafGauge = maf, "MAF Air flow", "g/sec", 0, 650, 0, 200, 480, 550, 0, 0 barometerGauge = barometer, "Barometer", "kPa", 60, 120, 0, 20, 200, 245, 1, 0 calcMapGauge = calcMAP, "Estimated MAP", "kPa", 0, 255, 0, 20, 200, 245, 1, 0 pulseWidth1Gauge = pulseWidth1, "Pulse Width 1", "mSec", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 pulseWidth2Gauge = pulseWidth2, "Pulse Width 2", "mSec", 0, 25.5, 1.0, 1.2, 20, 25, 3, 1 tachometer = rpm, "Engine Speed", "RPM", 0, 8000, 300, 500, 5000, 6000, 0, 0 throttleGauge = throttle, "Throttle Position", "%", 0, 100, -1, 1, 90, 100, 0, 0 ; timmingErrGauge = timingErr, "Timing Error", "degrees",-10, 10, -10, -5, 5, 10, 1, 1 deltaTGauge = deltaT, "Timing Delta", "uS", 0, 25000, 0, 0,25000, 25000, 0, 0 veBucketGauge = veTuneValue, "VE Value", "%", 0, 120, -1, -1, 999, 999, 0, 0 veGauge = veCurr1, "VE Current", "%", 0, 120, -1, -1, 999, 999, 0, 0 voltMeter = batteryVoltage, "Battery Voltage", "volts", 7, 21, 9, 10, 16, 17, 2, 2 warmupEnrichGauge = warmupEnrich, "Warmup Enrichment", "%", 100, 150, -1, -1, 101, 105, 0, 0 ; Name Var Title Units Lo Hi LoD LoW HiW HiD vd ld xTauGauge1 = xTauFuelCorr1, "X-Tau Correction1", "%", 0, 200, 40, 70, 130, 160, 0, 0 xTauGauge2 = xTauFuelCorr2, "X-Tau Correction2", "%", 0, 200, 40, 70, 130, 160, 0, 0 #if CELSIUS #if EXPANDED_CLT_TEMP cltGauge = coolant, "Coolant Temp", "C", -40, 600, 65, 93, 162, 176, 0, 0 matGauge = mat, "Intake Air Temp", "C", -40, 110, -15, 0, 95, 100, 0, 0 #else cltGauge = coolant, "Coolant Temp", "C", -40, 120, -15, 0, 95, 105, 0, 0 matGauge = mat, "Intake Air Temp", "C", -40, 110, -15, 0, 95, 100, 0, 0 #endif #else #if EXPANDED_CLT_TEMP cltGauge = coolant, "Coolant Temp", "°F", -40, 600, 150, 200, 325, 350, 0, 0 matGauge = mat, "Intake Air Temp", "°F", -40, 215, 0, 30, 200, 210, 0, 0 #else cltGauge = coolant, "Coolant Temp", "°F", -40, 250, 0, 30, 200, 220, 0, 0 matGauge = mat, "Intake Air Temp", "°F", -40, 215, 0, 30, 200, 210, 0, 0 #endif #endif e85Gauge = fuelCorrection,"E85 Fuel Correction", "%", 100, 200, 99, 99, 164, 170, 0, 0 ethanolGas = fuelComposition, "Ethanol Percentage","%", 0, 100, -1, -1, 85, 101, 0, 0 triggers± = trig_fix, "Triggers add/sub", "", -200, 200, -100, -10, 10, 100, 0, 0 tachCount = tachCount, "Number Tach Pulses", "", 0, 1000, -1, -1, 1000, 1000, 0, 0 ;------------------------------------------------------------------------------- [FrontPage] #if NARROW_BAND_EGO egoLEDs = 0.0, 1.0, 0.5 ; Voltage settings. #elif LAMBDA egoLEDs = 1.5, 0.5, 1.0 ; Lambda settings. #else egoLEDs = 19.7, 9.7, 14.7 ; Afr settings. #endif ; Gauges are numbered left to right, top to bottom. ; ; 1 2 3 4 ; 5 6 7 8 gauge1 = tachometer gauge2 = throttleGauge gauge3 = pulseWidth1Gauge #if NARROW_BAND_EGO gauge4 = egoGauge #elif LAMBDA gauge4 = lambda1Gauge #else gauge4 = afr1Gauge #endif gauge5 = mapGauge #if IAC_GAUGE gauge6 = IACgauge #elif PWM_GAUGE gauge6 = PWMIdlegauge #else ; FIDLE_GAUGE gauge6 = matGauge #endif gauge7 = advdegGauge gauge8 = dwellGauge ;---------------------------------------------------------------------------- ; Indicators ; expr off-label on-label, off-bg, off-fg, on-bg, on-fg ; indicator = { tpsaen }, "Not Accelerating", "AE", cyan, white, red, black ; ; Look in the new colorScheme.ini for the basic ones, add more or tell me what to add. indicator = { ECUType == 1 || ECUType == 2 }, "SET ECU!!", "ECU Set", red, black, white, green indicator = { crank }, "Not Cranking", "Cranking", white, black, black, white indicator = { startw }, "ASE off", "ASE ON", white, black, cyan, black indicator = { warmup }, "WUE off", "WUE ON", white, black, blue, white indicator = { tpsaen }, "Accel Enrich", "Accel Enrich", white, black, green, black indicator = { tpsden }, "Decel Cut", "Decel Cut", white, black, green, black indicator = { tps > floodClear && crank }, "Flood clear off", "FLOOD CLEAR ON", white, black, red, black indicator = { batteryVoltage < 10.5 }, "Battery OK", "Battery LOW", green, black, red, black indicator = { port0 }, "Port 0 Off", "Port 0 On", white, black, red, black ;------------------------------------------------------------------------------- [RunTime] barHysteresis = 2.5 ; Seconds #if CELSIUS #if EXPANDED_CLT_TEMP coolantBar = -40, 300 matBar = -40, 100 #else coolantBar = -40, 100 matBar = -40, 100 #endif #else #if EXPANDED_CLT_TEMP coolantBar = -40, 600 matBar = -40, 215 #else coolantBar = -40, 215 matBar = -40, 215 #endif #endif batteryBar = 6, 15 dutyCycleBar = 0, 100 #if NARROW_BAND_EGO egoBar = 0.0 , 1.0 #elif LAMBDA egoBar = 0.5, 1.5 #else egoBar = 9.7, 19.7 #endif gammaEBar = 0, 200 mapBar = 0, 255 pulseWidthBar = 0, 25.5 rpmBar = 0, 8000 throttleBar = 0, 100 egoCorrBar = 0, 200 baroCorrBar = 0, 200 warmupCorrBar = 0, 200 airdenCorrBar = 0, 200 veCorrBar = 0, 200 accCorrBar = 0, 100 ;------------------------------------------------------------------------------- [Tuning] #if NARROW_BAND_EGO egoLEDs = 0.0, 1.0, 0.5 ; Voltage settings. #elif LAMBDA egoLEDs = 1.5, 0.5, 1.0 ; Lambda settings. #else egoLEDs = 19.7, 9.7, 14.7 ; Afr settings. #endif ; font = "Lucida Console", 12 ; font = "Courier", 14 spotDepth = 2 ; 0 = no indicators, 1 = Z only, 2 = XYZ indicators. cursorDepth = 2 ; Same as spot depth. ; The four radio buttons on the tuning screen select a "page" of six ; gauges. The gauge numbering is the same as the front page, across ; then down. ; 1 2 ; 3 4 ; 5 6 ; ; gaugeColumns allows you to hide or show gauges in column 2 (i.e., ; gauges 2, 4 and 6). gaugeColumns = 2 ; Only 1 or 2 are valid. ; Page 1 Page 2 Page 3 Page 4 pageButtons = "&EGO", "&WUE", "PW&1", "PW&2" gauge1 = tachometer, tachometer, tachometer, tachometer gauge2 = mapGauge, mapGauge, mapGauge, mapGauge #if NARROW_BAND_EGO gauge3 = egoGauge, egoGauge, egoGauge, egoGauge #elif LAMBDA gauge3 = lambda1Gauge, lambda1Gauge, lambda1Gauge, lambda1Gauge #else gauge3 = afr1Gauge, afr1Gauge, afr1Gauge, afr1Gauge #endif gauge4 = egoCorrGauge, warmupEnrichGauge, pulseWidth1Gauge, pulseWidth2Gauge gauge5 = veBucketGauge, veBucketGauge, veBucketGauge, veBucketGauge gauge6 = accelEnrichGauge, accelEnrichGauge, dutyCycle1Gauge, dutyCycle2Gauge ;------------------------------------------------------------------------------- [AccelerationWizard] tpsDotBar = 0, 100 mapDotBar = 0, 200 ;------------------------------------------------------------------------------- [BurstMode] getCommand = "a\x00\x06" [OutputChannels] deadValue = { 0 } ; Convenient unchanging value. ochBlockSize = 112 ochGetCommand = "a\x00\x06" ; Lower case so we don't get confused. seconds = scalar, U16, 0, "s", 1.000, 0.0 secl = { seconds % 256 }, "s" ; For runtime screen. pulseWidth1 = scalar, U16, 2, "s", 0.001, 0.0 pulseWidth2 = scalar, U16, 4, "s", 0.001, 0.0 pulseWidth = { pulseWidth1 }, "s" ; For runtime screen. rpm = scalar, U16, 6, "RPM", 1.000, 0.0 advance = scalar, S16, 8, "deg", 0.100, 0.0 ; unsigned char squirt,engine,afrtgt1,afrtgt2; // afrtgt in afr x 10 squirt = scalar, U08, 10, "bit", 1.000, 0.0 ; Squirt Event Scheduling Variables - bit fields for "squirt" variable above ; inj1: equ 3 ; 0 = no squirt 1 = squirt ; inj2: equ 5 ; 0 = no squirt 1 = squirt ; sched1: equ 2 ; 0 = nothing scheduled 1 = scheduled to squirt ; firing1: equ 0 ; 0 = not squirting 1 = squirting ; sched2: equ 4 ; firing2: equ 1 firing1 = bits, U08, 10, [0:0] firing2 = bits, U08, 10, [1:1] sched1 = bits, U08, 10, [2:2] inj1 = bits, U08, 10, [3:3] sched2 = bits, U08, 10, [4:4] inj2 = bits, U08, 10, [5:5] engine = scalar, U08, 11, "bit", 1.000, 0.0 ; Engine Operating/Status variables - bit fields for "engine" variable above ; ready: equ 0 ; 0 = engine not ready 1 = ready to run ; crank: equ 1 ; 0 = engine not cranking 1 = engine cranking ; startw: equ 2 ; 0 = not in startup warmup 1 = in warmup enrichment ; warmup: equ 3 ; 0 = not in warmup 1 = in warmup ; tpsaen: equ 4 ; 0 = not in TPS acceleration mode 1 = TPS acceleration mode ; tpsden: equ 5 ; 0 = not in deacceleration mode 1 = in deacceleration mode ; mapaen: equ 6 ; 0 = not in MAP acceleration mode 1 = MAP deaceeleration mode; not implemented ready = bits, U08, 11, [0:0] crank = bits, U08, 11, [1:1] startw = bits, U08, 11, [2:2] warmup = bits, U08, 11, [3:3] tpsaen = bits, U08, 11, [4:4] tpsden = bits, U08, 11, [5:5] mapaen = bits, U08, 11, [6:6] afrtgt1 = scalar, U08, 12, "AFR", 0.100, 0.0 afrtgt2 = scalar, U08, 13, "AFR", 0.100, 0.0 ; unsigned char wbo2_en1,wbo2_en2; // from wbo2 - indicates whether wb afr valid wbo2_en1 = scalar, U08, 14, "", 1.000, 0.0 wbo2_en2 = scalar, U08, 15, "", 1.000, 0.0 ; int baro,map,mat,clt,tps,batt,ego1,ego2,knock, // baro - kpa x 10 ; // map - kpa x 10 ; // mat, clt deg(C/F)x 10 ; // tps - % x 10 ; // batt - vlts x 10 ; // ego1,2 - afr x 10 ; // knock - volts x 10 barometer = scalar, S16, 16, "kPa", 0.100, 0.0 map = scalar, S16, 18, "kPa", 0.100, 0.0 #if CELSIUS mat = scalar, S16, 20, "°C", 0.05555, -320.0 coolant = scalar, S16, 22, "°C", 0.05555, -320.0 #else mat = scalar, S16, 20, "°F", 0.100, 0.0 coolant = scalar, S16, 22, "°F", 0.100, 0.0 #endif tps = scalar, S16, 24, "%", 0.100, 0.0 tpsADC = { tps*10.23 }, "ADC" ; Fake for calibrator and file indexing. throttle = { tps }, "%" batteryVoltage = scalar, S16, 26, "v", 0.100, 0.0 afr1 = scalar, S16, 28, "AFR", 0.100, 0.0 afr2 = scalar, S16, 30, "AFR", 0.100, 0.0 lambda1 = { afr1 / 14.7 }, "Lambda" lambda2 = { afr2 / 14.7 }, "Lambda" knock = scalar, S16, 32, "v", 0.100, 0.0 ; egocor1,egocor2,aircor,warmcor, // all in % egoCorrection1 = scalar, S16, 34, "%", 1.000, 0.0 egoCorrection = { ( egoCorrection1 + egoCorrection2) / 2 }, "%" ; Alias for old gauges. egoCorrection2 = scalar, S16, 36, "%", 1.000, 0.0 airCorrection = scalar, S16, 38, "%", 1.000, 0.0 warmupEnrich = scalar, S16, 40, "%", 1.000, 0.0 fuelComposition = { (fuelCorrection - 100)*1.587 }, % ; works with default sensor values ; tpsaccel,tpsfuelcut,barocor,gammae, // tpsaccel - acc enrich(.1 ms units) ; // tpsfuelcut - % ; // barcor,gammae - % accelEnrich = scalar, S16, 42, "msec", 0.100, 0.0 tpsfuelcut = scalar, S16, 44, "%", 1.000, 0.0 baroCorrection = scalar, S16, 46, "%", 1.000, 0.0 gammaEnrich = scalar, S16, 48, "%", 1.000, 0.0 ; vecurr1,vecurr2,iacstep,cold_adv_deg; // vecurr - % ; // iacstep - steps ; // cold_adv_deg - deg x 10 veCurr1 = scalar, S16, 50, "%", 1.000, 0.0 veCurr2 = scalar, S16, 52, "%", 1.000, 0.0 veCurr = { veCurr1 }, "%" ; For runtime display. iacstep = scalar, S16, 54, "", 1.000, 0.0 idleDC = { iacstep } ; Close enough. coldAdvDeg = scalar, S16, 56, "deg", 0.100, 0.0 tpsDOT = scalar, S16, 58, "%/sec", 1.000, 0.0 mapDOT = scalar, S16, 60, "kPa/sec", 1.000, 0.0 dwell = scalar, S16, 62, "msec", 0.100, 0.0 maf = scalar, S16, 64, "g/sec", 0.010, 0.0 calcMAP = scalar, S16, 66, "kPa", 0.100, 0.0 ; Blend of MAP and TPS, depends on algorithm fuelCorrection = scalar, S16, 68, "%", 1.000, 0.0 ; Percent alcohol in fuel. portStatus = scalar, U08, 70, "bit", 1.000, 0.0 ; Spare port status bits port0 = bits, U08, 70, [0:0] port1 = bits, U08, 70, [1:1] port2 = bits, U08, 70, [2:2] port3 = bits, U08, 70, [3:3] port4 = bits, U08, 70, [4:4] port5 = bits, U08, 70, [5:5] port6 = bits, U08, 70, [6:6] knockRetard = scalar, U08, 71, "deg", 0.100, 0.0 xTauFuelCorr1 = scalar, S16, 72, "%", 1.000, 0.0 egoV1 = scalar, S16, 74, "Volts", 0.010, 0.0 egoV2 = scalar, S16, 76, "Volts", 0.010, 0.0 amcUpdates = scalar, S16, 78, "", 1.000, 0.0 kpaix = scalar, S16, 80, "kPa", 0.100, 0.0 xTauFuelCorr2 = scalar, S16, 82, "%", 1.000, 0.0 spare1 = scalar, S16, 84, "", 1.000, 0.0 spare2 = scalar, S16, 86, "", 1.000, 0.0 trig_fix = scalar, S16, 88, "", 1.000, 0.0 spare4 = scalar, S16, 90, "", 1.000, 0.0 spare5 = scalar, S16, 92, "", 1.000, 0.0 spare6 = scalar, S16, 94, "", 1.000, 0.0 spare7 = scalar, S16, 96, "", 1.000, 0.0 spare8 = scalar, S16, 98, "", 1.000, 0.0 spare9 = scalar, S16, 100, "", 1.000, 0.0 spare10 = scalar, S16, 102, "", 1.000, 0.0 tachCount = scalar, U16, 104, "", 1.000, 0.0 ospare = scalar, U08, 106, "", 1.000, 0.0 cksum = scalar, U08, 107, "", 1.000, 0.0 deltaT = scalar, U32, 108, "uS", 1.000, 0.0 ; Normalized time between trigger pulses, ; "fills in" missing teeth. accDecEnrich = { accelEnrich + (tpsden ? tpsfuelcut : 100) }, "%" time = { timeNow }, "s" rpm100 = { rpm / 100.0 } altDiv1 = { alternate ? 2 : 1 } altDiv2 = { alternate ? 2 : 1 } cycleTime1 = { 60000.0 / rpm * (2.0-twoStroke) }, "ms" nSquirts1 = { nCylinders/divider } dutyCycle1 = { 100.0*nSquirts1/altDiv1*pulseWidth1/cycleTime1 }, "%" cycleTime2 = { 60000.0 / rpm * (2.0-twoStroke) }, "ms" nSquirts2 = { nCylinders/divider } dutyCycle2 = { 100.0*nSquirts2/altDiv2*pulseWidth2/cycleTime2 }, "%" #if NARROW_BAND_EGO egoVoltage = { egoV1 }, "V" ; For LED bars... #elif LAMBDA egoVoltage = { lambda1 }, "Lambda" ; For LED bars... #else egoVoltage = { afr1 }, "AFR" ; For LED bars... #endif ; pageSize = 112 ;------------------------------------------------------------------------------- ;-- The entries are saved in the datalog file in the order in which they -- ;-- appear in the list below. -- ;-- -- ;-- Channel - Case sensitive name of output channel to be logged. -- ;-- Label - String written to header line of log. Be careful -- ;-- about changing these, as programs like MSLVV and -- ;-- MSTweak key off specific column names. -- ;-- Type - Data type of output, converted before writing. -- ;-- Format - C-style output format of data. -- [Datalog] ; Channel Label Type Format ; -------------- ---------- ----- ------ entry = time, "Time", float, "%.3f" entry = seconds, "SecL", int, "%d" entry = rpm, "RPM", int, "%d" entry = map, "MAP", float, "%.1f" entry = kpaix, "MAP/baro", float, "%.1f" entry = maf, "MAF", float, "%.1f" entry = throttle, "TP", int, "%d" entry = batteryVoltage, "vBatt", float, "%.2f" #if NARROW_BAND_EGO entry = egoVoltage, "O2", float, "%.3f" #elif LAMBDA entry = lambda1, "Lambda", float, "%.3f" #else entry = afr1, "AFR", float, "%.2f" #endif entry = mat, "IAT", float, "%.1f" entry = coolant, "CLT", float, "%.1f" entry = engine, "Engine", int, "%d" entry = egoCorrection, "Gego", int, "%d" entry = airCorrection, "Gair", int, "%d" entry = warmupEnrich, "Gwarm", int, "%d" entry = baroCorrection, "Gbaro", int, "%d" entry = gammaEnrich, "Gammae", int, "%d" entry = accDecEnrich, "AccelEnrich", int, "%d" entry = veCurr1, "Gve", int, "%d" entry = pulseWidth1, "PW", float, "%.3f" entry = dutyCycle1, "DutyCycle1", float, "%.1f" entry = veCurr2, "Gve2", int, "%d" entry = pulseWidth2, "PW2", float, "%.3f" entry = dutyCycle2, "DutyCycle2", float, "%.1f" entry = advance, "SparkAdv", float, "%.1f" entry = knockRetard, "knockRet", float, "%.1f" entry = coldAdvDeg, "ColdAdv", float, "%.1f" entry = dwell, "Dwell", float, "%.2f" entry = tpsDOT, "tpsDOT", int, "%d" entry = mapDOT, "mapDOT", int, "%d" entry = iacstep, "IAC", int, "%d" entry = deltaT, "deltaT", float, "%.0f" entry = trig_fix, "Trigger±", int, "%d" entry = tachCount, "tachCount", int, "%d" entry = xTauFuelCorr1 "XTau1", int, "%d" entry = xTauFuelCorr2 "XTau2", int, "%d" entry = fuelCorrection, "E85fuelCorr", int, "%d" entry = fuelComposition, "Ethanol%", int, "%d" entry = afrtgt1, "AFRtrgt1", float, "%.2f" ;-------------------------------------------------------------------------------